Publicité
IMPORTANT
Please read
these
instructions carefully before
you
start to assemble this carport.
Please
carry
out the
steps
in
the order
set
out
in
these instructions.
Keep
these instructions
in
a
safe
place for
future
reference.
»
Care
and Safety advice
Please
follow the instructions
as
listed
in
this manual.
Sort the parts and check against
the content
list.
For
safety purposes we
strongly recommend the product to
be assembled by at least
two
people.
Some parts have metal edges.
Please be
careful when
handling components.
Always wear gloves, shoes and safety goggles during assembly.
Do
not
attempt
to assemble the carport
in
windy
or
wet conditions.
Dispose
of
all
plastic bags safely
-
keep them
out of
reach
of
small
children.
Keep
children
away from the assembly
area.
Do
not
attempt
to assemble the carport if
you
are
tired,
have taken drugs, medications
or alcohol, or if you are
prone to dizzy
spells.
When using
a
stepladder or power tools,
make sure
that
you are
follow
the manufacturer's safety
advice.
Do
not climb
or stand on
the roof.
Heavy articles should not be leaned against
the
poles.
Please
consult your
local
authorities if
any
permits
are
required.
Keep
roof
and gutters clean
of
snow,
durt
& leaves.
Heavy
amounts
of
snow
on
roof
can
damage the carport making it
unsafe
to stand below
or nearby.
This
product
was
designed to
be used
mainly
as
a
carport.
If
color
was
scratched
during
assembly it
can be
fixed.
»
Cleaning instructions
When your carport needs cleaning,
use
a
mild detergent solution
and rinse
with
cold clean water.
Do
not
use
acetone, abrasive cleaners, or others
special
detergents to
clean
the
panel.
»
Required for assembly
(in
addition to the previously depicted tools)
1.8
wooden
beams,
minimum
6'
long
(1.8 m)
2.
Concrete
3.
Digging equipment, compatible with the
soil
type
and
required measurements
»
Before
starting assembly
This
carport must
be assembled on
a
solid
base (such
as
concrete
or asphalt).
Choose
your site carefully before beginning
assembly. Site surface
(mainly below
poles) needs
to
be level.
During assembly
use
a
soft platform below the parts to avoid
scratches and damages.
»
During Assembly
MWhen
encountering the information
icon, please refer
to the relevant assembly step for
additional comments
and assistance.
6,
Attention:
Tighten
all
screws at
the end
of
assembly.
Anchoring
this
product
to the
ground
is
essential
to
its
stability
and
rigidity.
It
is
required to complete this stage
in
order for your warranty to
be valid.
Please use
both
assembly instructions (Arizona
Wave
/
Breeze
+ Arizona
EZ
Link) in
order to assemble the product
Please
note there
are
2
types
of
glazing
in
addition to
2
assembly options: Wings
/
Arch,
as
shown
in
the first
page.
Make sure you
follow
the
pages
showing the product
you chose
to
assemble.
Follow the main instructions
of
the
Arizona
Wave
/
Breeze
after completing the relevant
steps
in
these instructions.
Wing Parking:
Step
1:
Dig
two
(2)
holes according
to the specified measurements and make sure the bottom
is
well
tightened.
Plan
ahead according
to the placement of the parking
as
shown
in
the drawing.
Make sure
the
pits' walls
are
at
a
90°
If
the ground
is
sandy and
digging proper
holes
is
impossible, please consult
a
local
expert
/
constructor.
*Carry out steps
1-4
in
the
Arizona
Wave
/
Breeze assembly instructions, prior to carrying
out
this step.
Step
2: Please use
wooden
beams
(not supplied) to
set
and hold the aluminum poles
in
place, make sure
the
profiles
are set at
a
depth of 19.6"
(50 cm)
in
accordance
with step
#4
in
the Arizona Wave/Breeze
assembly
instructions.
The
aluminum
poles must be leveled
in all
directions.
Step 3:
Please
note
and make sure
the concrete casting
reaches
the line that
was
marked
on
the profile
at
the
previous
steps.
*
Please
wait for the concrete
to be
fully
set
and dry,
in
accordance
with the manufacturer's instructions
and
depending
on
the weather conditions, before continuing with the
assembly!
Step 4:
Carry
out steps
7-8
in
the Arizona Wave
/
Breeze assembly instructions, prior to carrying out this step.
Please
note the profile's direction.
Step
5: Carry
out steps 10-17
in
the Arizona Wave
/
Breeze assembly instructions, prior to carrying out this
step.
Step 6:
Carry
out steps 18-19
in
the Arizona Wave
/
Breeze assembly instructions, prior to carrying out this
step.
Step
7: Carry
out steps 20-23
in
the Arizona Wave
/
Breeze assembly instructions, prior to carrying out this
step.
For
Arizona
Breeze
-
WINGS: After this step, proceed
with Arizona Breeze
assembly instructions.
Step 8:
Carry
out steps
24-31
in
the Arizona Wave assembly instructions, prior to carrying out this
step.
Step 9:
Lay
out
all
the
panels and make sure
they overlap, move one
set
of
panels at
a
time
in
order to connect
them to the roof with the supplied
screws.
After this
step,
proceed
with Arizona
Wave assembly instructions.
Arch Parking:
Step
10: Dig
(4)
holes
according to the specified measurements and make
sure
the
bottom
is
well
tightened.
Plan
ahead according to the placement
of the
parking
as
shown
in
the drawing.
Make sure
the pits' walls
are
at
a
90°.
If
the ground
is
sandy and
digging proper
holes
is
impossible,
please
consult
a
local
expert
/
constructor.
Step
11: Please use
wooden
beams (not supplied) to set and
hold the aluminum
poles
in
place, make sure
the
profiles
are set at
a
depth of
19.6" (50 cm) in
accordance
with step #4
in
the
Arizona Wave/Breeze
assembly
instructions.
The
aluminum
poles must be leveled
in all
directions.
Step
13:
Please
note and make
sure
the concrete
casting reaches the line that was marked
on
the profile
at
the previous
steps.
*
Please
wait for the concrete to
be
fully
set
and dry,
in
accordance
with the manufacturer's instructions
and
depending
on
the weather conditions, before
continuing with the
assembly!
Step
14: Carry
out steps 7-26
in
the
Arizona
Breeze assembly instructions, prior to carrying out this
step.
Step
16: Carry
out step
32
in
the
Arizona
Breeze assembly instructions, prior to carrying
out
this step.
Step 21:
In
order to
be able to insert the sealing strips,
perform gradually:
panel + sealing strip.
Step 23: After
this step, proceed
with Arizona Breeze
assembly instructions.
Step 24:
Carry
out steps 7-25
in
the
Arizona
Wave assembly instructions, prior to carrying
out
this step.
Step 27:
Carry
out steps
29-31
in
the
Arizona
Breeze assembly instructions, prior to carrying out this
step.
Step 28:
Lay
out
all
the panels and make sure they overlap, move one
set
of
panels
at
a
time
in
order to connect them to the roof with the supplied
screws.
After this
step,
proceed
with Arizona
Wave assembly instructions.
Publicité
