Publicité
IMPORTANT
Please read
these
instructions carefully before you start to assemble this carport.
Please
carry
out the
steps
in
the order
set
out
in
these instructions.
Keep these
instructions
in
a
safe
place
for future
reference.
Care
and Safety advice
Please
follow
the instructions
as
listed
in
this manual.
Sort the parts and check against the
content
list.
For
safety purposes we
strongly recommend the product to
be
assembled
by at least
two
people.
Some parts have metal edges.
Please be
careful when handling components.
Always wear gloves, shoes and safety goggles during assembly.
Do
not attempt to
assemble the carport
in
windy
or
wet conditions.
Dispose
of
all
plastic bags safely
-
keep
them out of
reach
of
small
children.
Keep
children away from the assembly
area.
Do
not attempt to
assemble the carport
if
you
are
tired,
have
taken drugs,
medications
or alcohol, or
if
you
are
prone to dizzy
spells.
When using
a
stepladder
or
power tools, make
sure
that
you
are
follow
the
manufacturer's safety advice.
Do
not climb
or stand on the roof.
Heavy
articles should not
be
leaned against the poles.
Please
consult your
local
authorities if
any
permits
are
required.
Keep
roof
and gutters clear
of
snow,
durt
& leaves.
Heavy
amounts of snow
on
roof
can
damage the carport making it
unsafe
to
stand below or nearby.
This
product
was
designed to
be used
mainly
as
a
carport.
If color
was scratched
during assembly it
can be
fixed.
Cleaning instructions
When
your carport
needs cleaning,
use
a
mild detergent solution
and rinse
with
cold clean water.
Do
not
use
acetone, abrasive cleaners, or others special detergents to clean the panel.
»
Required
for
assembly
(in
addition to the previously depicted tools)
1.
8
wooden
beams,
minimum
6'
long
(1.8 m)
2.
Concrete
3.
Digging equipment, compatible with the
soil
type
and required measurements
4. High step ladder,
minimum of
8
rungs
(8'/
2.4 m)
»
Before
starting
assembly
This
carport must
be
assembled on
a
solid
base (such
as
concrete or asphalt).
Choose
your
site
carefully before beginning assembly.
Site
surface (mainly below poles)
needs
to
be level.
During assembly
use
a
soft platform below the parts to avoid
scratches and damages.
»
During Assembly
P
When
encountering the information
icon, please refer
to the relevant
assembly step
for additional comments
and assistance.
qAttention:
Peel
the film covering the
panel.
Make sure you install it
with the
UV
protected
side up
(Step 29)
Tighten
all screws
at the end
of
assembly.
Anchoring this product to the ground
is
essential to
its
stability
and
rigidity.
It
is
required to complete this stage
in
order for your warranty to
be
valid.
Step
1:
Dig
two
(2)
holes according
to the specified measurements and
make sure
the bottom
is
well tightened.
Plan
ahead according to the placement
of
the parking
as
shown
in
the drawing.
Make sure
the pits' walls
are at
a
90°.
If
the ground
is
sandy and
digging proper
holes
is
impossible,
please
consult
a
local
expert
/
constructor.
Step
2:
Profiles
#8646
come covered
in
plastic film,
please do
not
peel at
this point, it
serves
to protect the profiles from the concrete.
These
profiles
assist
in
stabilizing the
concrete casting, and will
be
later assembled
in
the
roof.
Step
5: Please use
wooden
beams (not supplied) to set and
hold the aluminum
poles
in place,
make sure
the profiles
are set
at
a
depth
of
19.6" (50 cm) in accordance
with
the former step
(4).
The
aluminum
poles must
be
leveled
in
all
directions.
Step 6:
Please
note and make
sure
the concrete casting
reaches
the line
that
was
marked
on
the profile at the previous
steps.
Step
7: Please
wait for the concrete to
be
fully
set and dry,
in
accordance
with the
manufacturer's instructions and depending
on
the weather conditions, before
continuing with the
assembly!
Step 9:
Please
note the profile's direction.
Step
19:
Optional: if
you
find
it
difficult to tighten
the
screws, it
is
possible to
use
toggle
clamps before
tightening
the
screws. Make sure
the toggle clamps do not
come
in
direct contact with the powder
coated profiles!.
Use
a
wooden plank
in
order
to protect the profile from bending.
Step 33:
In
order to
be
able to
tighten
the
screws,
use
a
high step ladder.
Be
careful!
»
Notice the marks on
each step:
During assembly some
screws are
fastened
fully
by
wrench while others
are
fastened
just after the whole carport
is
assembled and leveled.
Cjii
Publicité
