Publicité
LEGENDE
ARTICLE 1 = M8 ECROUS (x2)
ARTICLE 2 = M8 RONDELLES (x2)
ARTICLE 3 = R&G BOBINES DE PROTECTION CRASH (B0442) (x2)
ARTICLE 4 = ENTRETOISE COTE DROIT 15mm DE LONG (S1004) (x1)
ARTICLE 5 = ENTRETOISE COTE GAUCHE 18mm DE LONG (S1003) (x1)
ARTICLE 6 = AXE (SB015) (x1)
NOTICE DE MONTAGE
En commençant du coté gauche, lorsqu'on est assis sur la moto, insérer une entretoise du coté gauche S1003
(Article 5) dans la tête de l'axe d'origine du coté gauch de l'axe avant.
Insérer une bobine de protection R&G (Article 3), une rondelle M8 (Article 2) et un écrou M8 nut (Article 1)
sur l'extrémité avec le filetage le plus court de l'axe (Article 6) du kit. Engager l'écrou de façon à ce que
l'insert de l'écrous soit complètement engagé.
Passer l'axe dans l'entretoise tout juste insérée dans la roue avant du coté gauche.
Placer l'entretoise restante
place dans le creux hexagonal de l'axe avant. Enfin, glisser la bobine de protection crash restante R&G
(Article 3) sur l'axe.
Insérer la rondelle restante et l'écrou (article 2 et 1
l'aide d'une clé de 13mm.
NE PAS TROP SERRER – Les écrous bloquent suffisamment.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The
Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those
in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for
its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify
any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the
motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a
replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise
than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident or
neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be
liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or
the fitting or service concerned. These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were
purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-
sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value
exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of
discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty
goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
OUTILS REQUIS
Clé à cliquet 2x 13mm
Clés en croix.
(S1004 – Article 4) sur l'extrémité dépassante de l'axe afin que l'entretoise se
ISSUE 1 07/02/2017 (HH)
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
R&G Racing
www.rg-racing.com
du kit sur
)
le filetage puis serrer les 2 écrous à
Email:
info@rg-racing.com
FP0192BK
Publicité
