Sharp XL-B514 Mode D'emploi page 9

CD player
To change to the CD player, short press
displays <CD>.The display will read <Reading>, followed by <No disc>,
if the CD compartment is empty.
Play a CD
NOTE: It is not possible to play DVD or computer CDs.
Press . The CD drawer will open and <Open> will be displayed.
Place CD onto the CD tray. Ensure that the CD is laying fl at on the tray.
Press to close the CD tray. <Reading> will be displayed and after a
short delay, the CD will start playing.
CD controls:
The following controls are possible when playing a CD:
Short press to play a CD. The track number and the elapsed time of
the track will be displayed. Press again to pause the CD. The elapsed time
will fl ash while music is paused.
Short press to move to next track. Long press to forward within a
track.
Press to move to previous track. Long press to rewind within a track.
Press to stop CD.
NOTE: If you stop or pause playing a CD for approximately 20 minutes, your
micro system will go into standby mode automatically.
Programmed play
Using your remote control, you can program the play order of up to 20
tracks on your CD.
NOTE: To set up programmed play, the CD must be stopped in the CD
compartment and must not be paused or playing.
While in CD mode:
In CD mode, with the CD you wish to programme in the CD
compartment and stopped:
Press to enter CD programmed play mode <T01 P01> will be
displayed.
Use or to go to the track number that you would like to program
to play fi rst. Press to confi rm.
You will now be able to select the second track that you would like to
program. Continue to select each track as above, up to a total of 20
tracks. Once you have added 20 tracks to the programmed play mode,
the display will read <Program full>.
Press or to move through the program.
Press to play the programmed tracks.
To exit programmed play mode, press
Caring for compact discs
• Do NOT touch the playback side of the CD.
• Do NOT attach paper or tape or any other material to the disc.
• Fingerprints and dust on the disc will cause sound deterioration. Wipe
the disc from the centre outwards with a soft cloth Always keep the
disc clean.
• If dust or marks cannot be removed with a soft cloth, wipe the disc
lightly with a slightly damp soft cloth and then wipe with a soft dry
cloth.
• Do NOT use any type of solvent, commercially available cleaners or
antistatic spray for vinyl as it may damage the disc.
• Do NOT store discs in a place subject to direct sunlight or near a heat
source.
• Do NOT store discs in a place subject to moisture or dust, such as a
bathroom or near a humidifi er.
until the micro system
twice.
USB mode
Ensure your micro system is in USB mode by short pressing
the micro system displays <USB>.
Insert the USB stick which has the MP3 fi les you wish to play into the
USB input.
NOTE: If the USB does not insert easily, try rotating it by 180 degrees and try
again. Never force the USB stick into the socket or try to insert it at an angle
as this could damage the socket.
NOTE: USB drives up to 64GB FAT32 are supported.
The following controls are available when using a USB:
Short press to Play/Pause.
Short press to move to previous track. Long press to rewind within
a track.
Short press to move to next track. Long press to forward within a
track.
Press to stop.
NOTE: To navigate the folders on the USB, use
control.
Aux in mode
To change to an Aux-input, short press
displays <Aux in>.
Use a 3.5mm audio input connection cable (not included) for a quick and
easy connection to an external audio source.
Connect one end of the 3.5mm audio connection cable to the
headphone (or auxiliary out) socket of your secondary device, connect
the other end to the Aux in socket on the rear of your micro System.
Press the Play button on your external device to start playback through
the micro System speakers.
To gain optimal volume levels, adjust the output volume level on both
the secondary device and on the micro System.
NOTE: It is recommended that you unplug the Audio cable from the Aux in
socket after you have fi nished listening to your external device.
EN
until
and on the remote
until the micro system