Publicité
Les langues disponibles
Les langues disponibles
10. Plug the power cord into a 120 Volt AC electrical outlet.
11. Press the On/Off button to turn the blender on. The power light will
blink, indicating the product is active and ready to use.
12. Select the desired Pre-Programmed setting or Manual Setting. To change
your selection, press Stop followed by another Pre-Programmed Setting or
Manual Setting.
®
13. Your Oster
Blender features 2 pre-programmed settings for superior
results at the touch of a button. Simply select one of the pre-
programmed settings: Smoothie/Cocktail or Dip/Salsa and the blender
will cycle through that program delivering professional results every time.
14. When using the Pre-Programmed Setting, the blender will automatically
stop when the program is finished. The blinking blue light indicates that
the blender is ready for use.
15. Press the On/Off button to turn the blender off.
16. To use Low Pulse or High Pulse, push and hold down the desired Pulse
button for the desired length of time. Release and allow blade to stop.
Repeat cycle as desired.
NOTE:
With Dual Direction Blade Technology, the Crush
Pro 6™ Blade automatically reverses to keep
ingredients moving down the jar, making blade jams
virtually nonexistent.
Blending Tips
•
Put liquids in the Blender Jar first, unless a recipe says otherwise.
• Crushing ice: Crush 6 ice cubes or approximately 2 cups of ice. Cover ice
with about 1 cup or 0.236 liters of water for best results.
• Do not remove the Blender Lid while in use. Remove Filler Cap to add
smaller ingredients. (Figure 7)
• Cut all firm fruits and vegetables, cooked meats, fish and seafood into pieces
no larger than 3/4 inch (1.9 cm) to 1 inch (2.5 cm). Cut all kinds of cheeses
into pieces no larger than 3/4 inch (1.9 cm).
• This Blender will not mash potatoes, whip egg whites or substitute dairy
toppings, mix stiff dough or grind raw meat.
I
C
Ce
rushIng
Without Liquid: Use Pulse button until you achieve desired results.
With Liquid: Add desired amount of ice cubes and water until ice floats. Blend on
High until you achieve desired results then strain off water.
F
7
igure
E5
Hot Foods
• Open the Filler Cap to vent steam. Tilt Filler Cap away from you. Keep
hands away from the cover opening to prevent possible burns.
• When working with hot liquids, remove Filler Cap and start blending at
a low speed. Then move to a faster speed. DO NOT add liquid over the
4 cup (0.946 liter) level.
Cleaning Your Blender
WARNING: Unplug before cleaning. Do not immerse the blender base in
water or any other liquid.
Use a damp, soft sponge with mild detergent to clean the outside of the
Blender Base. All parts except for the Blender Base are dishwasher-safe. Place
Sealing Ring in bottom basket of dishwasher. You can also wash the parts in
warm, soapy water. Rinse well and dry.
e
C
F
asY
lean
eature
Quickly and conveniently clean blending jar between uses without removing
the blade from the jar.
•
Pour 3 cups (0.709 liter) of warm water in the blender Jar.
•
Add 1 – 2 drops of liquid dishwashing detergent.
Select Low speed.
•
Run blender for 20-30 seconds then press OFF button.
•
•
Empty jar of soapy water into sink and rinse the jar thoroughly
with clean water.
NOTE:
Easy clean is not a substitute for regular cleaning described in the
"Cleaning Your Blender" section above. It is especially important to
disassemble and thoroughly clean your blender when processing milk,
meats, seafood, and eggs.
NOTE:
This appliance has no user serviceable parts. Servicing should be
performed by an authorized service representative.
Please see the warranty information section for further information.
Storing Your Blender
After cleaning, reassemble Blade System to Blender Jar with Sealing Ring and
Blender Jar Bottom Cap. Store Blender with cover ajar to prevent container odor.
E6
Publicité
