DeWalt DXV34P-QT Traduction De La Notice D'instructions Originale page 17

English
Description (Fig. A)
WARNING : Never modify the power appliance or
any part of it. Damage or personal injury could result.
Top handle/cord wrap
1
Power cord
2
On/off switch
3
Vacuum head
4
Lid latches
5
Dust tank
6
Hose
7
Casters
8
Clean Connect TM Filter
9
Vacuum port
10
Hose strap
11
Disposable Dust Bag
12
ASSEMBLY AND ADJUSTMENTS (Fig. A–C)
WARNING: To reduce the risk of injury, turn
appliance off and disconnect appliance from
power source before installing and removing
accessories, before adjusting or changing
set-ups or when making repairs. An accidental
start-up can cause injury.
WARNING: The filters
place while vacuuming, except as described
under Wet Pick Up Applications under Operation.
When vacuuming fine dust, you may also use an
additional paper dust bag to make emptying the
canister easier.
1.Install the disposable dust bag
in Figure B.
NOTE: Be careful not to tear the bag. Place bag
securely onto vacuum port
seal for maximum dust collection performance.
2.Place the vacuum head
secure it by closing the lid latches
3.Insert end of hose into clip-in hose vacuum
7
port and tighten the end of hose on to the tank.
10
OPERATION
Instructions for Use (Fig. A, D, E)
WARNING: Always observe the safety instructions
and applicable regulations.
WARNING: To reduce the risk of injury,
turn appliance off and disconnect
appliance from power source before
installing and removing accessories,
before adjusting or changing set-ups or
when making repairs. An accidental start-up can
cause injury.
1.Plug the power cord into an appropriate outlet.
2.Turn the on/off switch
3
3.Your D WALT construction dust extractor is fitted
E
with the D WALT connection system. The allows for
E
a fast, secure connection between the hose
and power tool. The connector
must always be in
9
as shown
12
to provide a tight
10
onto the dust tank and
4
.
5
to the ON position ( I ).
7
connects
13
directly to D WALT compatible tools or through the
E
use of an adapter (available from your local D
supplier). Refer to the Accessories section for detail
on available adapters.
NOTE: If using an adapter ensure it is firmly
attached to the tool outlet before following the steps
below.
OPERATING INSTRUCTIONS
Caster installation (Fig. A, F)
1.Invert the dust box and install the casters to the bottom
of the dust tank and fix them with screws.
2.Return dust tank assembly upright.
Accessory bag holder assembly (Fig. A, F)
Attach 2 accessory bag holder brackets to
tank with 4 self-tapping screws provided.
Remove / Change Used Dust Collection
Bag (Fig. A)
WARNING: Appropriate personal protective
equipment like dust mask and gloves should be used
while handling used dust bags.
1.Turn off vacuum and unplug cord from outlet.
2.Unlatch lid latches
5
3.Pull the disposable dust bag carefully from vacuum
port .
10
4.Seal the disposable dust bag opening tightly when
removing it from the machine.
5.Dispose disposable dust bag in appropriate container
according to statutory provisions.
Wet Pick Up Applications (Fig. A, G)
WARNING: If foam or liquid escapes from the
machine,switch off immediately.
CAUTION: Clean the water level limiting device
regularly and examine it for signs of damage.
Refer to Fig. G.
NOTICE: DO NOT remove ball float
will cause damage to the vacuum. The ball float keeps
water from entering the motor.
Before using the vacuum for wet pick up:
• Ensure the canister is empty and free of excessive dust.
• Remove filters .
9
WARNING: Do not use the machine with this set
up for dust Class L.
To Empty Canister (Fig. A, G)
The ball float valve 14 will block air to the motor when
the canister is full and the sound of the motor will
change at once.
When the motor has a high pitched sound and air/
water flow stops, empty the canister.
1.Turn off vacuum and unplug cord from outlet.
2.Unlatch lid latches
5
head .
4
3.Empty contents of dust tank
container or drain.
To Convert Back to Dry Vacuum
Operation (Fig. A)
1.Empty Canister, refer to To Empty Canister
instructions.
15
WALT
E
and remove vacuum head
, doing so
14
and remove vacuum
into a suitable
6
.
4