Mitsubishi Electric Mr.SLIM PLA-M35EA Manuel D'utilisation page 10

3. Operation
3.5.2 Vane·Vent. (Lossnay)
<Accessing the menu>
Main Main menu
Operation
F1 F2 F3 F4
Operation
Vane·Louver·Vent. (Lossnay)
High power
Comfort
Main menu:
Cursor
en
F1 F2 F3 F4
Vane (vertical air direction) setting
<3D i-See sensor supported>
Fri
Auto Ind. Low
Auto
Vert Horiz i-see Vent.
F1 F2 F3 F4
<3D i-See sensor not supported>
Fri
Swing Low
Vert Horiz Vent.
F1 F2 F3 F4
Louver (horizontal air direction) setting
<3D i-See sensor supported>
Fri
Auto Auto Ind. Low
Vert Horiz i-see Vent.
F1 F2 F3 F4
8
Select "Operation" from the Main
menu (refer to 3.5.1), and press the
[SELECT] button.
Select "Vane·Louver·Vent.
(Lossnay)" or "Vane·3D i-See·Vent.
(Lossnay)" from the Operation
menu, and press the [SELECT]
button.
<3D i-See sensor supported>
Press the [F1] button.
<3D i-See sensor not supported>
Press the [F1] or [F2] button.
Press the button as indicated above
to go through the following setting
options.
Auto
Auto Step 1 Step 2
Step 3 Step 4 Step 5
Swing
Swing
Select "Swing" to move the vanes
up and down automatically.
When set to "Step 1" through
"Step 5", the vane will be fixed at
the selected angle.
<3D i-See sensor supported>
Press the [F2] button.
<3D i-See sensor not supported>
Press the [F3] button.
When the horizontal air direction
function is supported, the following
setting options are available.
Front Auto Swing
<3D i-See sensor not supported>
Fri
Swing Low
Vert Horiz Vent.
F1 F2 F3 F4
3D i-See sensor setting
This setting cannot be made when the 3D i-See sensor function is not
supported.
* Refer to the indoor unit Instruction Book to see if the unit supports the
function or not.
<3D i-See sensor supported>
Fri
Auto Auto Ind. Low
Vert Horiz i-see Vent.
F1 F2 F3 F4
Ventilation setting
<3D i-See sensor supported>
Fri
Auto Ind. Low
Auto
Vert Horiz i-see Vent.
F1 F2 F3 F4
<3D i-See sensor not supported>
Fri
Swing Low
Vert Horiz Vent.
F1 F2 F3 F4
<Returning to the Main menu>
Operation
Vane·Louver·Vent. (Lossnay)
High power
Comfort
Main menu:
Cursor
F1 F2 F3 F4
<3D i-See sensor supported>
Press the [F3] button to go through
the following setting options.
Off Indirect
Direct Area
When set to "Indirect," "Direct," or
"Area," the vartical and horizontal
air direction settings will be fixed to
"Auto."
<3D i-See sensor supported/not
supported>
Press the [F4] button to go through
the following setting options.
Off Low High
Off Low
• The fan on some models of indoor
units may be interlocked with
certain models of ventilation units.
Press the [RETURN] button to go
back to the Operation menu.
High