Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1)
Dust bag
(2)
Protective guard
(3)
Transport handle
(4)
Handle
(5)
Lock-off function for On/Off switch
(6)
Laser warning label
(7)
Retracting blade guard
(8)
Fence
(9)
Workpiece support (flexibly pluggable)
(10)
Saw table
(11)
Locking knob for all mitre angles
(12)
Mitre pre-setting lever
(13)
Angle indicator for mitre angles
(14)
Scale for mitre angles
(15)
Screw clamp
(16)
Folding fence
(17)
Guide roller
(18)
Chip deflector
(19)
On/off switch
(20)
On/Off switch for laser (cutting line indication)
(21)
Holes for screw clamp
(22)
Chip ejector
(23)
Mounting holes
(24)
Clamping bolt for all bevel angles
(25)
Transport safety lock
(26)
Recessed handles
(27)
Spindle lock
(28)
Hex key
(29)
Laser beam outlet aperture
(30)
Angle indicator for bevel angles
(31)
Scale for bevel angles
(32)
Guide rail for length gauge
(33)
Clamping screw for length stop
(34)
Wing bolt for fixing the guide rail for length gauge
(35)
Length stop
(36)
Insert plate
(37)
Hex socket screw for mounting the saw blade
(38)
Clamping flange
a)
(39)
Saw blade
(40)
Inner clamping flange
(41)
Wing bolt for adjusting the height of the threaded
rod
(42)
Threaded rod
(43)
Wing bolt for screw clamp
Bosch Power Tools
(44)
Screw clamp pins
(45)
Detents for standard mitre angles
(46)
Screws for insert plate
(47)
Set screw for positioning the laser
(48)
Set square
(49)
Hex socket screw for fence
(50)
Stop screw for 0° bevel angle
(51)
Stop screw for 45° bevel angle
(52)
Screw for bevel angle indicator
(53)
Screw for mitre angle indicator
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Mitre saw
Article number
Rated power input
No-load speed
Laser type
Laser class
Weight according to EPTA-Pro-
cedure 01:2014
Protection class
Permitted workpiece dimensions (maximum/minimum): (see "Per-
missible workpiece dimensions", page 31)
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
The appliance meets IEC 61000-3-11 requirements and is
subject to conditional connection. The appliance can lead to
occasional voltage fluctuations under unfavorable power
conditions. The impedance of this appliance is set as Z
= 0.101 Ω. The user must make sure, that the connection
point, with the impedance Z
, on which the appliance shall
max
be plugged in meets the impedance requirement: Z
≥ Z
. If Z
is unknown, determine Z
tual
max
max
with the network supplier or supply authority.
Values can vary depending upon the product and are subject to ap-
plication and environmental conditions. For further information
www.bosch-professional.com/wac.
Dimensions of suitable saw blades
Saw blade diameter
Base blade thickness
Max. cutting width
Hole diameter
Noise Information
Noise emission values determined according to
EN IEC 62841-3-9.
English | 27
GCM 254
3 601 M52 0..
W
1750
–1
min
5000
nm
650
mW
< 1
2
kg
11.1
/ II
actual
ac-
in consultation
max
mm
254
mm
1.4–2.5
mm
3
mm
30
1 609 92A 8KE | (09.05.2023)