holzkraft HWS 505 K Traduction Des Instructions D'origine page 29

Additional accessories bag enclosed for protective flap with handle (Fig. 18)
2x saw guard
1x tension spring
2x hexagon screw M8x35
2x hexagon nut M8
6x hexagon nut, self-locking
1x hexagon screw M8x12
6x Philips screw M4x10
6x locking nut M4
3x hexagon screw M8x20
3x collar bushing D 8mm
3x washer D 8mm
8. Assembly
For packaging reasons, the swivel log saw does not come fully assembled. It must be assembled on a completely
level surface.
A. Place the packaging, cardboard or similar on the floor to prevent damage. Remove the base frame from the packaging and posi-
tion the machine with the swivel side on top (Fig. A).
B. Lift wheel axle slightly, slide one washer (10) and one wheel (7) (for external side see Fig. B3, B4) onto the axle on each side. Fit
lock washer (11) on the axle with the saw blade wrench and knock onto the shaft with the hammer. (Secure lock washer against
falling with adhesive tape) (Fig. B1 - B4).
C. Mount foot left and right (4 a, b) on the base frame, each with 4 lenticular flange head screws M8x16 (8 a) and locking nut M8 (8
b) (Fig. C1 - C4). Lightly tighten all frame screws by hand.
D. Screw rear strut (3) onto the mounted feet with 4 lenticular flange head screws M8x16 (8 a) and locking nut M8 (8 b). Mount strut
left and right (6 a, b) on the side of the feet (4 a, b), each with 5 lenticular flange head screws M8x16 (8 a) and locking nut M8
(8 b). (Fig. D1, D2, D3).
E. Place machine on the feet, cut the cable tie, release the locking lever and tilt the swivel out.
screws well. It is important here that the swivel log saw stands on a level surface. Mount swivel protection (17) on the inside of
the swivel with 2 mushroom head screws M6 x 12, 2 washers 6mm and 2 self-locking nuts M6 respectively and tighten securely.
Make sure that the mushroom head screws are guided in from the outside. (Fig. E3).
F. Mount guard bracket (15) on the right rear foot with 2 lenticular flange head screws M8x16 (8 a) and locking nut M8 (8 b). (Fig. F)
G. Take the protective hood with protective cover (14 and 16) out of the packaging, loosen 2 hexagon screws top and bottom and
remove the protective cover. To ease assembly, remove the front saw blade flange. Slide protective hood (14) over the saw blade
flange, fasten and secure with 5 lenticular flange head screws M8x16 (8 a) and locking nut M8 (8 b). (Fig. G1, G2, G3).
H. Mount and fasten protective cover (14) with the 2 hinges on the protective hood using 2 hexagon screws M6x12 (9 a) and 2 lock-
ing nuts M6 (9 b). (Fig. H1, H2, H3).
I. Mount complete guard panel with clinch stud (13a), to do so guide 1 hexagon screw M5 x 12 (13e) through the screw-mounted
protective hood from the saw blade side, slide plastic washer (13b), cover panel (13a) and plastic bush (13g) onto the hexagon
screw (13e) and then tighten a little with the self-locking hexagon nut M5 (13h). It must be possible for the cover panel to move.
Slide plastic washer (13b) onto the threaded bolt of the cover panel (13a) and guide into the circular recess. Slide on galvanised
pivot bushing (13c) and secure with self-locking hexagon nut M5 (13d). (Fig. I1, I2, I3, I4, I5). Now lightly tighten both threaded
connections. It must be possible for the panel to move easily.
J. Position the saw blade, screw on by hand with flange, washer and hexagon nut. Insert locking pin and tighten the nut well using
the saw blade wrench. Remove locking pin once more. (J1, J2, J3, J4). Important note! When inserting the saw blade, make sure
the direction of rotation is correct. Always wear gloves when inserting and tightening the saw blade.
K. Close blade guard and secure top and bottom with the hexagon screws (Fig. K).
L. Guide electrical cable through the frame feet, screw and secure switch with 2 fillister head screws M4x60 and locking nut. Place
saw blade wrench and locking pin (2) in the recess (Fig. L).
GB
(Fig. 18a)
(Fig. 18b)
(Fig. 18c)
(Fig. 18d)
(Fig. 18e)
(Fig. 18f)
(Fig. 18g)
(Fig. 18h)
(Fig. 18j)
(Fig. 18k)
(Fig. 18m)
(Fig. E1, E2). Tighten all frame
page: 29