HammerSmith HydroBlast PRO Mode D'emploi page 11

Do not use water, petrol, alcohol or other
chemical solvents. The water inlet filter
and the water pipe filter should be cleaned
regularly.
• Used batteries should be recycled and not
simply disposed of in the bin.
• Do not use the included charger for any other
appliance.
• Do not charge at high temperatures.
• Only ever charge indoors, and avoid the
device getting wet in the rain.
• If the power cord is damaged, it must
be replaced by the manufacturer, its
maintenance department or similar
professionals, in order to avoid any danger.
• Before charging, please ensure that the
charger is in good operating condition.
• Improper use of a high-pressure jet lance can
be dangerous. Do not aim the high-pressure
jet directly at people, animals, electrical
devices or the cleaner itself.
• Do not splash water on devices that contain
electrical components.
• The device must not be used if it has been
dropped, has visible signs of damage, or is
leaking.
CHARGING THE BATTERY (#2)
To charge, connect the battery to the charger and
firmly insert the plug into the socket. It takes 4
hours to fully charge the battery. During charging,
the LED on the charger lights up red, when
charging is complete, the LED lights up green. After
charging, unplug the charger.
INSERTING THE BATTERY (#3)
To insert a fully charged battery into the device,
simply insert it into the device base as shown in
Figure #3, and press until it clicks into place. To
remove, press the red button on the battery pack,
and pull it out.
M36209_Hammersmith_HydroBlast PRO_Manual_20240221_SR.indd 11 M36209_Hammersmith_HydroBlast PRO_Manual_20240221_SR.indd 11
INSTALLING THE LONG-RANGE NOZZLE (#4-5)
1. Take the long-range nozzle and mount it on the
device.
2. To assemble, firmly insert the end of the nozzle
into the opening on the device (you will feel
resistance), and then turn it to the left so that the
barrel locks firmly into place.
Note: Only hand-tighten.
Removing the long-range nozzle: To remove the
long-range nozzle, gently push it inward towards
the gun, and quickly turn it to the right to loosen
and remove it.
INSTALLING A MICRO-SCREEN NANOFILTER (#6 + #7)
Note: The nanofilter and high-pressure hose adapter
are already pre-installed on the device when it is
delivered. Hold the flexible high-pressure hose and
the nanofilter micro-sieve.
Insert the tip of the flexible high-pressure hose into
the socket of the nanofilter micro-sieve. Make sure the
filter is seated correctly and tightly.
Tip: If the hose is difficult to insert, take a cup of hot
water, dip the tip of the hose into the hot water, and
leave it there for a few minutes. This loosens-up the
flexible rubber hose and allows it to expand, making it
easier to insert and connect.
INSTALLING THE HIGH-PRESSURE FLEXIBLE
HOSE ADAPTER (#8-11)
1. Take the other end of the flexible 5-metre high-
pressure hose and the hose adapter.
2. Turn the bottom cover of the hose adapter anti-
clockwise to expose the tip of the adapter.
3. Thread the end of the flexible hose through the
bottom adapter cover, and insert the tip of the
adapter into the end of the hose. Make sure the
adapter is secure.
4. Place the adapter cover back onto the thread
of the adapter, and tighten everything in a
clockwise direction.
USE WITH A BUCKET OR GARDEN HOSE
Note: the device is fitted with a safety switch. In order
to be able to press the on/off button, you must turn the
safety switch inwards/press it to the left.
1. a) with high-pressure hose and bucket (#12):
Connect the high-pressure hose to the main unit.
You will hear a clicking sound. Place the other end
of the hose, including the nanofilter micro-sieve, in
a bucket with clean water. Hold the main unit firmly,
press the safety switch on the handle to the left,
and press the power button on the handle. Keep
the button pressed while using. You need to keep
the button pressed for around 15 seconds until the
pressure builds up and pressurized water comes
11
21.02.24 16:41 21.02.24 16:41