Publicité
Les langues disponibles
Les langues disponibles
OPERATING PRECAUTIONS
WARNING: HOT WHILE IN OPERATION. DO
NOT TOUCH THE STOVE. KEEP CHILDREN,
CLOTHING AND FURNITURE AWAY.
CONTACT MAY CAUSE SKIN BURNS.
CAUTION: ENSURE THAT THE FIREPOT AND
THE PAN UNDERNEATH ARE CLEAN AND IN
THE PROPER OPERATING POSITION BEFORE
USING THE STOVE.
WARNING: NEVER USE GASOLINE,
GASOLINE-TYPE LANTERN FUEL, KEROSENE,
CHARCOAL LIGHTER FLUID, OR SIMILAR
LIQUIDS TO START OR 'FRESHEN UP' A FIRE
IN THIS HEATER. KEEP ALL SUCH LIQUIDS
WELL AWAY FROM THE HEATER WHILE IT IS
IN USE.
PAINT CURING
To allow the paint to bond durably to the stove, start
by running the stove on P1 Maximum Power for at
least 60 minutes. Provide cross ventilation to eliminate
odors or smoke cause by this curing process.
OPERATING PROCEDURE: TURN ON STOVE
NOTE: If the display screen indicates that the
stove is "Switching Off" the stove can not
be interrupted. The Display Message will
highlight to indicate that the state will not be
changed. Only once the "Switching Off" cycle
has finished and the exchanger has cooled
can the stove be turned back on again.
1. Plug power cord into socket on the rear bottom of
stove and press the red ON/OFF toggle switch above
it to ON. See Figure 16.
ON/OFF
Switch
Figure 16
Power Socket/ON/OFF Switch
NOTE: TO PREVENT STOVE FROM BEING OPERATED,
TURN OFF RED POWER SWITCH ON
BOTTOM, REAR OF STOVE.
Grand Teton Wood Pellet Fire Stove
Power Socket
2. Make sure that seals on the ash drawer and door
are in good condition. If the stove has never been
run before, add a handful of pellets directly to the
firepot. Close the ash drawer and doors securely,
and check that all side panels are all properly
installed.
NOTE: DO NOT USE GRATES, IRONS, OR ANY
OTHER METHODS OF SUPPORTING WOOD
PELLET FUEL. ONLY THE FIREPOT SPECIFIC
TO YOUR MODEL OF STOVE MAY BE USED.
3. Open the hopper. Ensure that there are a
sufficient number of pellets to satisfy your heating
requirements. Close the hopper.
4. Press and hold the power icon for 3 seconds on the
display panel. The stove will begin to automatically
progress through the following stages:
• Cleaning Cycle: The firepot draws dust, ash, &
remnants out.
• Feeding Cycle: Pellets will be transported from the
Pellet Hopper into the fire pot by the auger. This
can take 5 to 15 minutes depending on the model
of stove.
• Lighting Cycle: The electrically powered hot surface
igniter will run the entire lighting cycle and for a
couple minutes after the stove reaches stabilizing
and also begin combustion of the pellets in the
firepot. The heater will remain in the Lighting Cycle
until the exhaust smoke reaches a designated
temperature.
• Stabilization Cycle: The heater adjusts to fine
tune the stove output to the desired temperature.
Stabilizing will continue until the stove reaches the
thermostat desired temperature.
5. The stove has been successfully turned on.
OPERATING PROCEDURE: TURN OFF STOVE
NOTE: THE STOVE MAY BE TURNED OFF,
REGARDLESS OF WHAT CYCLE THE DISPLAY
SCREEN INDICATES THAT THE STOVE IS IN,
BY DEPRESSING AND HOLDING THE POWER
BUTTON FOR TWO SECONDS. ONCE THE
DISPLAY SCREEN INDICATES THAT THE
STOVE IS IN THE STABILIZATION CYCLE
PRESS THE POWER BUTTON AGAIN. THE
STOVE WILL ENTER THE COOLING CYCLE,
STATED ON THE DISPLAY SCREEN.
CAUTION: AFTER THE COOLING CYCLE THE
STOVE AUTOMATICALLY BEGINS
THE PROCESS OF CYCLING ON.
14
Operating Instructions and Owner's Manual
Publicité
