Publicité
Les langues disponibles
Les langues disponibles
• Do not overreach. Keep proper footing and balance at
all times.
• Never leave blower running unattended. Turn
power off.
• Remove the battery pack before connecting the tube.
• Store idle units. When not in use, the unit should be stored
in a dry, high or locked-up place - out of reach of children.
• Instructions for compatible batteries and chargers are
included for reference in this manual. Read all instruction
manuals included with your battery pack or charger. Read all
cautionary markings on the charger and battery pack.
• Disconnect the battery pack from the blower before
making any adjustments, changing accessories,
servicing, moving or storing the unit. Such
preventative safety measures reduce the risk of starting the
appliance accidentally.
SAVE THESE
INSTRUCTIONS
Additional Safety Information
WARNING:
or any part of it. Damage or personal injury could result.
WARNING:
Everyday eyeglasses are NOT safety glasses. Also use face or
dust mask if operation is dusty. ALWAYS WEAR CERTIFIED
SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection.
WARNING:
chemicals known to State of California to cause cancer, birth
defects or other reproductive harm. Some examples of these
chemicals are:
• compounds in fertilizers,
• compounds in insecticides, herbicides and pesticides,
• arsenic and chromium from chemically treated lumber.
To reduce your exposure to these chemicals, wear approved
safety equipment such as dust masks that are specially
designed to filter out microscopic particles.
• Avoid prolonged contact with dust from power
sanding, sawing, grinding, drilling, and other
construction activities. Wear protective clothing and
wash exposed areas with soap and water. Allowing dust
to get into your mouth, eyes, or lay on the skin may promote
absorption of harmful chemicals.
WARNING:
generate and/or disperse dust, which may cause serious and
permanent respiratory or other injury. Always use NIOSH/
OSHA approved respiratory protection appropriate for the
dust exposure. Direct particles away from face and body.
WARNING:
personal hearing protection that conforms to ANSI
S12.6 (S3.19) during use. Under some conditions and
duration of use, noise from this product may contribute to
hearing loss.
Never modify the power tool
ALWAYS use safety glasses.
Some dust contains
Use of this tool can
Always wear proper
CAUTION:
on its side on a stable surface where it will not cause a
tripping or falling hazard. Some tools with a large battery
pack will stand upright but may be easily knocked over.
• Air vents often cover moving parts and should be
avoided. Loose clothes, jewelry or long hair can be caught in
moving parts.
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
OPM .................... oscillations per
minute
A ......................... amperes
W ........................ watts
or AC ........... alternating current
ASSEMBLY AND ADJUSTMENTS
WARNING:
serious personal injury, turn unit off and remove
the battery pack before making any adjustments or
removing/installing attachments or accessories. An
accidental start-up can cause injury.
Blow Tube Assembly (Fig. B)
WARNING:
without tube securely in place. Never reach down into
housing through tube hole.
WARNING:
when you leave blower unattended or when storing, checking,
adjusting, cleaning, or working on blower.
• To attach the blower tube
up the peg
6
of the power head with the notch
blower tube opening as shown in Fig. B.
• Push the blower tube onto the power head until the tube
locks engage the blower tube and an audible click is heard.
• Pull on the tube to ensure it is securely in place.
• To remove the tube, press in and the two tube locks and
pull tube off.
English
When not in use, place tool
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
n o ....................... no load speed
n ......................... rated speed
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
..................... avoid staring at
light
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
..................... read all
documentation
IPXX .................... IP symbol
To reduce the risk of
Do not operate blower
Always remove the battery
to the power head, line
3
7
of the
5
Publicité
