Publicité
Les langues disponibles
Les langues disponibles
necessary. Press Start / Pause / Cancel button to start the
machine.
C
The loading door will not open if the water temperature
in the machine is high or the water level is above the
door opening.
4.17 Child Lock
Use Child Lock function to prevent children from tampering
with the machine. Thus you can avoid any changes in a
running programme.
C
You can switch on and off the machine with On / Off
button when the Child Lock is active. When you switch
on the machine again, programme will resume from
where it has stopped.
To activate the Child Lock:
Press and hold 2
and 4
Auxiliary Function buttons for 3
nd
th
seconds. "Con" appears on the display.
C
Same phrase will appear on the display if you press
any button when Child Lock is enabled.
To deactivate the Child Lock:
Press and hold 2
and 4
Auxiliary Function buttons for 3
nd
th
seconds. "COFF" appears on the display.
C
Do not forget to disable the child lock at the end of
the programme if it was enabled before. Otherwise,
machine will not allow to select a new programme.
4.18 Cancelling the programme
Press and hold Start / Pause / Cancel button for 3 seconds.
Start symbol flashes. Symbol of the step at which the
programme was cancelled remains lit. "
display and the programme is cancelled.
C
If you want to open the loading door after you have
cancelled the programme but it is not possible to open
the loading door since the water level in the machine
is above the loading door opening, then turn the
Programme Selection knob to Pump+Spin programme
and discharge the water in the machine.
4.19 Machine is in Rinse Hold mode
Spin symbol flashes and Pause symbol illuminates when the
machine is in Rinse Hold mode.
If you want to spin your laundry when the machine is in this
mode:
Adjust the spin speed and press Start / Pause / Cancel
button. Pause symbol disappears and Start symbol appears.
Programme resumes, discharges the water and spins the
laundry.
If you only want to drain the water without spinning:
Just press Start / Pause / Cancel button. Pause symbol
disappears. Start symbol appears. Programme resumes and
discharges the water only.
4.20 End of programme
"End" appears on the display at the end of the programme.
Symbols of the programme steps remain lit. Auxiliary
function, spin speed and temperature that were selected at
the beginning of the programme remain selected.
4.21 Your machine is equipped
with a "Standby Mode"
In case of not starting any programme or waiting without
making any other operation when the machine is turned
on by On/Off button and while it is in selection step or if
17 / EN
no other operation is performed approximately 2 minutes
after the programme you selected has come to an end,
your machine will automatically switch to energy saving
mode. Brightness of indicator lights will decrease. Also,
if your product is equipped with a display showing the
programme duration, this display will completely turn off. In
case of rotating the Programme Selection knob or pressing
any button, lights and display will restore to their previous
condition. Your selections made while exiting the energy
saving mode may change. Check the appropriateness of
your selections before starting the programme. Readjust if
necessary. This is not a fault.
5 Maintenance and cleaning
Service life of the product extends and frequently faced
problems decrease if cleaned at regular intervals.
5.1 Cleaning the detergent drawer
Clean the detergent drawer at regular intervals (every
4-5 washing cycles) as shown below in order to prevent
accumulation of powder detergent in time.
1. Press the dotted point on the siphon in the softener
C
End
" appears on the
2. Wash the detergent drawer and the siphon with plenty of
3. Insert the drawer back into its place after cleaning and
If your detergent drawer is the one indicated in the following
figure:
C
5.2 Cleaning the loading door and the drum
Residues of softener, detergent and dirt may accumulate
in your machine in time and may cause unpleasant odours
and washing complaints. To avoid this, use the Drum
Cleaning programme. If your machine is not featured with
Drum Cleaning programme, use Cottons-90 programme
and select Additional Water or Extra Rinse auxiliary
functions as well. Run theBefore starting the programme,
put max. 100 g of powder anti-limescale into the main
compartment and pull towards you until the compartment
is removed from the machine.
If more than normal amount of water and softener
mixture starts to gather in the softener compartment, the
siphon must be cleaned.
lukewarm water in a washbasin. Wear protective gloves
or use an appropriate brush to avoid touching of the
residues in the drawer with your skin when cleaning.
make sure that it is seated well.
Lift the rear part of the siphon to remove it as illustrated.
After performing the above mentioned cleaning
procedures, replace the siphon back to its seating and
push its front section downwards to make sure that the
locking tab engages.
Washing Machine / User's Manual
Publicité
