AEG CX7-1-30EB Mode D'emploi page 7

ENGLISH
Thank you for choosing an AEG CX7 Classic vacuum cleaner. In order to
ensure the best results, always use original AEG accessories and spare parts.
They have been designed especially for your vacuum cleaner. This product
is designed with the environment in mind. All plastic parts are marked for
recycling purposes.
DESCRIPTION OF CX7 CLASSIC
A. ON/OFF button
B. Power regulation button
C. ON/OFF button, hand unit
D. Locking screw
E. Release button, hand unit
F. Wallholder
G. Charging cable (with adapter)
H. Charging plug
I. Fine filter (inner filter)
J. Pre filter (outer filter)
K. Release button, dust container
L. Dust container
BEFORE STARTING
Check that the package includes all parts described in this instruction
manual and read this manual carefully. Pay special attention to the safety
precautions chapter. Save these instructions.
1
Assemble the handle.
2
A) Make sure that CX7 Classic is on a stable and horizontal surface away
from heat sources, direct sunlight or wet places. Attach the wall holder
to the wall 104 cm above the floor with a suitable screw and wall plug.
Make sure to use a correct wall plug for the wall. B) Attach the handle
to the wall holder. C) Connect the charging cable to the back side of the
vacuum cleaner.
3
Insert the adaptor into the mains and charge CX7 Classic. The charging
indicator will be lit when CX7 Classic is on charge.
CHARGING CX7 CLASSIC
4
When fully charged, the charging indicator will blink slowly. The num-
bers of LED lamps will indicate the level of charge. Full charging time is
around 4 hours. For better battery performance, charge CX7 Classic for
24 hours before first use and always keep it on charge when not used.
VACUUMING WITH CX7 CLASSIC
Before vacuuming, check that the nozzle wheels and the brush roll are
clean from sharp objects in order to avoid scratching sensitive floors
and to ensure full cleaning performance.
5
Start and stop CX7 Classic by pushing the ON/OFF button.
CX7 Classic will start on the high power mode.
For more silent cleaning and longer runtime, press the power regula-
tion button.
VACUUMING FURNITURE, CAR SEATS ETC.
6
Press the button to release the hand unit from the main body.
7
Attach the crevice nozzle to facilitate cleaning of areas difficult to reach.
Attach the brush on the crevice nozzle for dusting.
8
The crevice nozzle and small brush can be stored in the slot on the back
side of the handle.
EMPTYING OF THE DUST CONTAINER
9
Remove the dust container by pressing the buttons.
10
Take out the filters from the dust container by pressing the release but-
tons. Empty the contents into a dustbin. Never wash the dust container
or filters in a dishwasher.
IMPORTANT - FILTER CLEANING!
11
Pull the filter cleaning rod (B) to its end position and release it to
remove dust from the inner filter. Repeat 5 times.
12
The filters must be cleaned at regular intervals to ensure a high clean-
ing performance. Take out the filters by pressing the release buttons.
Separate the inner filter from the outer filter.
13
Rinse the filter parts carefully under lukewarm water without using any
detergents. (Never use the dishwasher or washing machine.) S hake to
remove excess water and leave to dry minimum 12h before putting
them back into the cleaner.
www.aeg.com
Nova_Classic_AEG_2017-12-20.indd 7
M. Dusting brush
N. Crevice nozzle
O. Cable protector grill
P. Hatch cover for brush roll
Q. Brush roll
R. Charging indicator
S. Cliff hanger
T. Slot for accessory storage
CLEANING THE HOSE AND NOZZLE WHEELS
14
Loosen the hose behind the nozzle from its upper connection. Remove
any object or debris that can be blocking the airflow in the hose or in
the air channel to the dust cup, and put the hose back.
15
If the wheels need to be cleaned or get jammed, remove them carefully
by using a flat screwdriver.
REMOVING AND CLEANING THE BRUSH ROLL
16
If the brushroll gets blocked C X7 Classic will stop. Open the cable pro-
tector grill and the brush roll hatch cover and remove the brush roll.
17
Us e a pair of scissors to remove threads etc. Reassemble the brush roll,
making sure it can spin freely.
REMOVING THE BATTERIES FOR RECYCLING
Warning; Battery removal must only be done by an AEG service
center or official collection point!
18
Only remove batteries if the product is to be scrapped. Improper han-
dling of the batteries may be hazardous. Batteries should always be
completely discharged before removal. Take your product to an AEG
service center or official collection point for recycling. They can remove
and recycle the battery and electric parts in a safe and professional way.
Follow your country's rules for collection of rechargeable batteries and
electrical products.
Enjoy a great cleaning experience with CX7 Classic!
DE
GB
EL
ES
FR
IT
NL
PT
AR
FA
7
2017-12-20 08:07:18