Publicité
Les langues disponibles
Les langues disponibles
RECIRCULATING
A
INSTALLATION OVERVIEW
A1.
Attach Mounting Plate to Wall
A2.
Prepare Top Cabinet
A3.
Check Blower Plate
Mount the Microwave Oven
A4.
Install or change Charcoal Filter
A5.
IMPORTANT NOTES:
•
Make sure the screws for the blower motor and blower
plate are securely tightened when they are reinstalled.
This will help to prevent excessive vibration.
•
Make sure the motor wiring has been properly routed
and secured, and that the wires are not pinched.
A1.
ATTACH THE MOUNTING
PLATE TO THE WALL
Attach the plate to the wall using toggle bolts.
At least one wood screw must be used to attach
the plate to a wall stud.
NOTE: If the cabinet depth including the cabinet doors
is more than 13" " ' ' then the unit must be spaced
13" MAX.
(33 cm)
Cabinet
Installation Instructions
(Non-Vented Ductless)
EN-10
3/8" TO EDGE
Trim the rear wall template
along the dotted line.
12"
NOTE: IT IS VERY IMPORTANT
TO
THE DIRECTIONS
READ AND FOLLOW
IN THE INSTALLATION
INSTRUCTIONS
BEFORE PROCEEDING
WITH THIS
REAR WALL TEMPLATE.
serves to position the bottom
4"
This Rear Wall Template
mounting plate and to locate
the horizontal exhaust
outlet.
1. Use a level to check
that the template is positioned
accurately.
one stud on the left or
2. Locate and mark at least
right side of the centerline.
least one wood
It is important to use at
a stud to support the weight
screw mounted firmly in
two additional, evenly spaced
of the microwave. Mark
toggle bolts.
3. Drill holes in the marked
locations for the supplied
locations. Where there
is
a stud, drill a 3/16" hole
for wood screws. For holes
that do not line up with
a stud, drill 5/8" holes for
toggle bolts.
DO NOT INSTALL THE
MOUNTING PLATE
AT THIS TIME.
4. Remove the template
from the rear wall.
book for your
5. Revie
w
e Installation Instruction
h t
installation situation.
Darle vuelta a la hoja
para consultar la
versión en Español.
Locate and mark holes
to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE
STUD ON EITHER SIDE
OF
THE CENTERLINE.
EVENLY
MARK THE LOCATION
FOR 2 ADDITIONAL,
SPACED TOGGLE BOLTS
IN THE MOUNTING
PLATE
AREA.
Locate and mark holes
to align with holes in the
m
o
u
t n
n i
g
l p
t a
. e
IMPORTANT:
OF
LOCATE AT LEAST ONE
STUD ON EITHER SIDE
THE CENTERLINE.
EVENLY
MARK THE LOCATION
FOR 2 ADDITIONAL,
along the dotted line.
SPACED TOGGLE BOLTS
IN THE MOUNTING PLATE
Trim the rear wall template
AREA.
1
Remove the toggle wings from the bolts.
2
Insert the bolts into the mounting plate through
the holes designated to go into drywall and
reattach the toggle wings to
each bolt.
To use toggle bolts:
Spacing for Toggles
More Than Wall
Thickness
Toggle Wings
Mounting
Toggle
Plate
Bolt
Wall
3
Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall
to mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure the bott m of the mounting plate
touch the bottom of the cabinet when pushed flush
against the wall and that the plate is properly
centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
Tighten all bolts. Pull the plate away from the wall
4
to help tighten the bolts.
3
⁄
" (19 mm) onto
4
Bolt End
o
Publicité
