LAZER LiNK Manuel D'utilisation page 4

from the mobile phone depending on its functions and
configuration. All of the call functions are maintained when
you are listening to music. If you receive an incoming call,
the music stops and when the call ends it returns. The same
happens when you make a call.
PAIRING IN INTeRCOm
WITH ANOTHeR LAZeR LINK DeVICe
Make sure that the two Lazer Links are switched off (switch off
as well any Bluetooth ® device that could be associated to the
Lazer Link, such as mobile phone, GPS, etc.). Press and keep
the control button (A) of both Lazer Links pressed until the
LEDs (A1) on both devices start to flash alternately in Red and
Blue. Then, briefly press the control button of one of the Lazer
Link devices. After a few seconds, both devices are paired
and you can establish the intercommunication.
When they have been associated, we recommend switching
off both Lazer Links and switching on the other devices
associated to each Lazer Link (GPS, mobile, etc.) then, switch
the Lazer Links back on, end the activation of the Intercom
function by pressing 2 seconds on the control button (A) of
one of the Lazer Links.
N.B.: It is important to associate each Lazer Link to its
respective Bluetooth ® device (GPS, mobile, etc.) before the
association of the two Lazer Links between themselves.
MEG Lazer Link bichro 135 X 80 mm DEF.indd 6-7
When two Lazer Links are in intercommunication, the
incoming call functions with the respective mobiles are
maintained. If you receive an incoming call the Intercom
stops and when the call ends it returns. The other device
in Intercom, which is not receiving the call, will receive an
acoustic warning signal. If you wish to make a call, you have
to deactivate the intercom first.
INTERCOM FUNCTIONS BETWEEN TWO LAZER LINK
ACTIVATE AND DEACTIVATE INTERCOM
When both Lazer Links are in a range of less than 10 metres
from one another, switched on and paired with their
respective mobiles, in order to establish the connection in
Intercom, press the control button (A) of one of the devices
for a couple of seconds, until you hear an acoustic signal.
The intercommunication between the two Lazer Links will be
activated then. To deactivate the intercommunication, press
the control button (A) of one of the Lazer Links for a couple
seconds.
INTERCOM VOLUME ADJUSTMENT
The Lazer Links allow changing their volume level when they
are in Intercom. Each time you press the control button (A)
the volume level changes in a cycle of three levels (low ->
medium -> high -> low...)
- 6 -
PAIRING IN INTeRCOm WITH ANOTHeR DeVICe OR
ANOTHeR AUDIO ReCeIVeR BLUeTOOTH ® DeVICe
(LAZeR BLUe OR LAZeR RINGO)
Make sure that the two devices to be associated are
switched off. Press and keep the control button (A) of the
Lazer Link pressed until the LED (A1) starts to flash in Red and
Blue. Set the other Bluetooth device in pairing mode. Then
®
briefly press the control button (A) of the Lazer Link once.
After a few seconds, both devices are paired and you can
establish the intercommunication. When they have been
associated, we recommend to switch off the Lazer Link and
to switch on the other devices (GPS, Mobile, etc.), then turn
the Lazer Link back on and activate the intercom function by
pressing 2 seconds on the control button (A).
When the Lazer Link is in intercommunication, the incoming
call functions with your mobile are maintained. If you receive
an incoming call the Intercom stops and when the call
ends it returns. The other device in Intercom will receive an
acoustic warning signal. If you wish to make a call with the
Lazer Link you have to deactivate the Intercom first.
INTERCOM FUNCTIONS WITH ANOTHER DEVICE
OR ANOTHER AUDIO RECEIVER BLUETOOTH DEVICE
®
(LAZER BLUE OR LAZER RINGO)
ACTIVATE AND DEACTIVATE INTERCOM
The Lazer Link can activate or deactivate intercommunication
with another Bluetooth ® device. To establish a connection
in Intercom, the two devices should be in a range of less
than 10 metres from one another, switched on and paired.
Then press the control button (A) on the Lazer Link for a
couple of seconds until you hear an acoustic signal. The
intercommunication will then be activated. To deactivate
it press and keep the control button (A) of the Lazer Link
pressed for a couple of seconds.
INTERCOM VOLUME ADJUSTMENT
The Lazer Links allow changing their volume level when they
are in Intercom. Each time you press the control button (A)
the volume level changes in a cycle of three levels (low ->
medium -> high -> low...).
SPeCIFICATIONS
Bluetooth : 2.1 Class 2
®
Profiles: A2DP, HSP, HPF, EDR.
Battery: Lithium polymer, that will provide up to 7 hours talk
time and up to 200 hours standby time (depending on
configuration and use of the device).
- 7 -
21/11/12 11:48