LAZER LiNK Manuel D'utilisation page 3

UK
WeLCOme
Congratulations and thank you for choosing the Lazer
Link, the innovative handfree Bluetooth system especially
®
designed for the Lazer helmets to allow easy and safe audio
communication in motion.
The Lazer Link is compatible with all audio Bluetooth
transmitting devices in HSP, HFP and A2DP profiles (Mobile,
GPS, MP3, MP4, or any device compatible with all of the
aforementioned functions). It can also be associated
(paired) with any Bluetooth audio receiver device, or to
®
another Lazer Link, establishing an audio communication
(intercommunication) up to a distance of approximately
10 metres, maintaining the association with the mobile or
corresponding device at the same time.
This device can be fully operated with only one control
button (A). A single LED (red/blue) (A1) is the indicator of
its functions: pairing, charging, on/off, low battery indicator.
The Lazer Link weighs only 55g approximately. In order to get
the best use out of your Lazer Link, please read this manual
thoroughly, and then keep it in a safe place for later use or
visit http://www.lazerhelmets.com/fr/innovations-2/lazer-link
MEG Lazer Link bichro 135 X 80 mm DEF.indd 4-5
CHARGING THe LAZeR LINK
Before using the Lazer Link for the first time, the battery (D)
must be fully charged. Plug the charger (F) into the socket,
and then insert the other end of the cable to the Lazer Link
mini-USB jack (B)
While the battery is charging the red LED (A1) is on, and will
turn off once it is fully charged.
NOTE: Never unplug the devices by pulling from the cable.
NOTE: It is recommended to completely charge the battery
®
each time, this will extend the battery life time.
NOTE: When the battery is charged completely but has not
been used for a long time, it may have less energy storage
than normal. After being used and recharged a few times,
the energy storage will increase back to normal.
INSTALLING THe LAZeR LINK
See the video on "how to install the Lazer Link" on our website:
http://www.lazerhelmets.com/fr/innovations-2/lazer-link
PAIRING WITH A mOBILe OR NAVIGATOR (GPS)
To be able to use the Lazer Link you have to associate it with
the Bluetooth ® device you want to connect it to (Mobile, GPS,
etc.). To do this, when the Lazer Link is switched off, press
and keep the control button (A) pressed until the LED (A1)
- 4 -
starts to flash alternately in Red and Blue. When looking for
Bluetooth ® devices in the mobile or navigator, you should find
the device called "Lazer Link". Select the "Lazer Link" device
and if requested enter the 0000 access code.
SWITCHING ON / SWITCHING OFF
To switch on your Lazer Link press and hold the control button
(A), until you hear a beep audio sound in the speaker (C)
and the LED (A1) starts to blink in a blue colour.
To switch off your Lazer Link press and hold the control button
(A) for a couple of seconds, until you hear a beep sound in
the speaker and the LED (A1) starts to blink in a red colour
and then off.
CALL FUNCTIONS
ANSWERING AND ENDING A CALL
When there is an incoming call, the speaker will play an
acoustic signal.
To answer the call, you can say any word out loud into the
microphone (E) (for example: "Answer!") or press the control
button (A) just once, or, as long as your mobile phone allows
it, you can activate the automatic answering function on the
mobile phone.
To end the call, press the button (A) just once or wait for the
caller to hang up.
REJECTING AN INCOMING CALL
To reject an incoming call, you just have to press the control
button (A) twice when you hear a call acoustic signal.
MAKING A CALL
To make a call, press the control button (A) to activate the
voice dialing function of the associated mobile (the mobile
should be configured to allow voice dialing, as long as the
mobile has this function).
To make a re-call (repetition of the last dialed number), press
the control button twice (A). It also depends on the mobile's
functions and configuration.
VOLUME ADJUSTMENTS
WITH MOBILE OR NAVIGATOR (GPS)
The Lazer Link device comes programmed with a volume level
that allows perfect listening up to 120 km/h. Use the volume
control of the associated device to adjust the volume. It is
recommended to set the highest volume level of the Lazer
Link with the control button (A) before the connection of the
other device (see p.6 "INTERCOM VOLUME ADJUSTMENT").
LISTENING TO THE MOBILE'S MUSIC
After connecting the Lazer Link to the mobile phone that can
play music by Bluetooth , when the music is activated in the
®
mobile it will be immediately heard through the Lazer Link
device. The music and the volume can only be controlled
- 5 -
21/11/12 11:48