Panasonic WV-CW970 Mode D'emploi page 35

**PRESET POSITION**
1
5*
9* 10*
13* 14*
17* 18*
21* 22*
25* 26*
29* 30*
ID:DOOR
033-064 225-256
RET TOP
(3) Home Position Setting (HOME POSITION)
A currently configured preset position can be
designated as the home position.
Pressing the HOME button of the system controller will
cause the camera to move to the currently specified
home position. Use the following procedure to make a
preset position the home position.
1. Move the cursor to HOME POSITION, and then tilt
the joystick left or right to select the position
number of the preset position you want to make the
home position.
This causes the preset position whose position
number you select to become the home position. If
you do not want to use the home position function,
select OFF for the HOME POSITION setting.
(4) Self Return Setting (SELF RETURN)
The self return setting can be used to specify automatic
return to a particular mode if a certain amount of time
elapses without any operation being performed.
1. Move the cursor to SELF RETURN, and then tilt the
joystick left or right to select a self return trigger setting.
Tilting the joystick cycles through the self return
display in the sequence shown below. (unit: sec,
min)
OFF ↔ 1S ↔ 2S ↔ 3S ↔
60MIN
↔ ↔
30MIN 20MIN 10MIN
2. If you selected any setting other than OFF in step 1,
press the CAM (SET) button and then tilt the
joystick left or right to select a self return mode.
OFF ↔ AUTO ↔ HOME ↔ APAN ↔ SEQ ↔ SORT
TRK ↔ PTR4 ↔ PTR3 ↔ PTR2 ↔ PTR1
OFF : In the auto mode, exits the auto mode
when the trigger time elapses.
AUTO (AUTO MODE setting not OFF) : Returns to
the auto mode when the trigger time
elapses.
AUTO (AUTO MODE setting OFF) : Returns to the
home position when the trigger time
elapses.
HOME : Returns to the home position when the
trigger time elapses.
APAN : Activates auto pan when the trigger
time elapses.
SEQ : Activates the sequence function when
the trigger time elapses.
SORT : Activates the sort function when the
trigger time elapses.
2* 3* 4*
6* 7* 8*
11* 12*
15* 16*
19* 20*
23* 24*
27* 28*
31* 32*
....... ↔ 10S ↔ 20S ↔ 30S ↔ 40S
↔ ↔ ↔
5MIN 3MIN 2MIN
PTR 1 to 4 : Activates the patrol function when the
TRK
Notes:
• The HOME setting should be selected when you
want to normally leave the camera in the home
position and occasionally perform pan and tilt,
or when you want to activate SEQ.
• PTR1-4 displays only the set number of patrol
routines (page 37).
(5) Auto Mode Setting (AUTO MODE)
Use the auto mode setting to specify the camera
movement mode (OFF, SEQ, SORT, AUTO PAN,
PATROL 1~4, AUTO TRACK).
After selecting AUTO PAN, you can use the AUTO PAN
setting menu to configure detailed settings.
1. Move the cursor to AUTO MODE, and then tilt the
joystick left or right to select a camera movement
mode setting.
OFF
SEQ
SORT : Sequentially
AUTO PAN:Camera pans automatically within the range
50S
↔
1MIN
PATROL 1 to 4:Operates the camera in accordance
AUTO TRACK:Auto tracking is done for moving
Tilting the joystick cycles through settings in the
sequence shown below.
OFF ↔ SEQ ↔ SORT ↔ AUTO PAN ↔ PATROL1 ↔ PATROL2
AUTO TRACK ↔ PATROL4 ↔ PATROL3
Notes:
• The auto mode is exited automatically whenever
manual
performed if AUTO PAN is operating and
PAN/TILT does SEQ, SORT, PATROL, or AUTO
TRACK movement. Note, however, that that the
contents of the setting menu do not change. To
return to the auto mode, open the setup menu
and then close it again. The auto mode will also
activate when the self return trigger time (this
page) elapses.
• During operation, the lens may enter the refresh
mode.
• PATROL1-4 displays only the set number of
patrol routines (page 37).
-35-
trigger time elapses.
: After the trigger time elapses, the
camera returns to the home position and
then automatic tracking starts. Following
that, after a set time, the camera returns
to the home position and auto tracking
repeats.
: Manual movement only
: Sequentially switches
positions in position number sequence.
(sequential movement)
switches
positions counterclockwise, starting from
the camera home position. (sort movement)
specified by PAN. Selecting AUTO PAN and
pressing the CAM (SET) button will display the
AUTO PAN setting menu, which can be used
for configuring detailed settings. (page 36)
with patrol function settings.
objects.
PAN/TILT or
between preset
between preset
ZOOM/FOCUS is