DIP Switch 1
ON
1
2
3
4
5
6
7
8
ON
1
2
3
4
5
6
7
8
ON
1
2
3
4
5
6
7
8
ON
1
2
3
4
5
6
7
8
ON
1
2
3
4
5
6
7
8
ON
1
2
3
4
5
6
7
8
ON
1
2
3
4
5
6
7
8
ON
1
2
3
4
5
6
7
8
ON
1
2
3
4
5
6
7
8
Notes:
• When using the Unit Number "1 ~ 96" setting, the unit number setting needs to be configured using the RS485
SET UP menu. For details about configuring this setting, see step 2 on page 20.
• Turning on power when this setting is selected causes the RS485 SET UP menu to appear during the initialization
routine.
RS485 Communication Parameters (DIP Switch 1)
Configuring DIP Switch 1 as shown below resets communication parameters to their factory default settings. You can
then change the settings as desired.
Table-2
DIP Switch 1
ON
1
2
3
4
5
6
7
8
ON
1
2
3
4
5
6
7
8
ON
1
2
3
4
5
6
7
8
ON
ON
1
2
3
4
5
6
7
8
Procedure to setup dip switch 1
(1) Turn off the camera and use DIP Switch 1 to configure RS485 Communication Parameters as shown in Table-2.
(2) Turn on the camera.
This applies the setting you configured in step (1).
(3) Turn off the camera, use DIP Switch 1 to set the unit number (as shown in Table-1), and then turn the camera
back on again.
Unit
DIP Switch 1
Number
ON
69
1
2
ON
70
1
2
ON
71
1
2
ON
72
1
2
ON
73
1
2
ON
74
1
2
ON
75
1
2
ON
76
1
2
ON
77
1
2
This setting resets communication parameters to the factory default settings.
BAUD RATE : 19 200 bit/s, DATA BIT : 8 bit, PARITY CHECK : NONE, STOP BIT : 1 bit
BAUD RATE : 9 600 bit/s, DATA BIT : 8 bit, PARITY CHECK : NONE, STOP BIT : 1 bit
BAUD RATE : 4 800 bit/s, DATA BIT : 8 bit, PARITY CHECK : NONE, STOP BIT : 1 bit
Unit
Number
78
3
4
5
6
7
8
79
3
4
5
6
7
8
80
3
4
5
6
7
8
81
3
4
5
6
7
8
82
3
4
5
6
7
8
83
3
4
5
6
7
8
84
3
4
5
6
7
8
85
3
4
5
6
7
8
86
3
4
5
6
7
8
Setting Description
-14-
DIP Switch 1
Number
ON
1
2
3
4
5
6
7
8
ON
1
2
3
4
5
6
7
8
ON
1
2
3
4
5
6
7
8
ON
1
2
3
4
5
6
7
8
ON
1
2
3
4
5
6
7
8
ON
1
2
3
4
5
6
7
8
ON
1
2
3
4
5
6
7
8
ON
1
2
3
4
5
6
7
8
ON
1
2
3
4
5
6
7
8
Unit
87
88
89
90
91
92
93
94
95