Publicité
Les langues disponibles
Les langues disponibles
WARNINGS AND CAUTIONS:
• TO AVOID FIRE, SHOCK, OR DEATH: TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring or servicing ixture!
• TO AVOID FIRE, SHOCK, OR DEATH: this control is to be used with ceiling fans that are rated 120VAC, total load 1.5 Amperes maximum.
• To be installed and/or used in accordance with appropriate electrical codes and regulations.
• If you are unsure about any part of these instructions, consult an electrician.
• Use this device with copper or copper clad wire only.
• The Decora
®
DDF01 Fan Speed Control is not compatible with standard 3-way or 4-way switches. It must be used with a Decora Digital remote for multi-location control, such as the DD00R-DL.
• Maximum wire length from dimmer to all installed remotes cannot exceed 300 ft.
INTRODUCTION
The next generation of fan speed control technology is here with the
new Decora
®
Digital Fan Speed Control with Bluetooth
®
Technology.
This innovative device works using the Leviton Decora
Digital
®
Dimmer & Timer app that can be easily downloaded to smartphones or
tablets and paired to the Leviton Fan Speed Control using Bluetooth
®
technology. Decora
Digital Devices give users point-to-point local
®
control to automate lighting and fan speed control, bridging the gap
between standard dimmers, fan speed controls and whole-house
automation systems.
The Decora
®
Digital Fan Speed Control is a powerful device –
combining the best of Leviton fan speed functions with today's mobile
technology for impressive results. The simple touch of a inger following
the intuitive on-screen guide makes it more convenient than ever to
manage fan speed.
Use of the app allows greater lexibility for accurate fan speed
functionality and makes pushing buttons for timed events a tedious
chore of the past.
The Leviton Decora
®
Digital Dimmer & Timer app can be easily
downloaded to mobile devices and is compatible with Android and iOS
smartphones or tablets. The app is easy to use with simple, intuitive
on-screen menu options to independently control dimmers and
switches throughout the home.
Decora
®
Digital Devices are ideal for living rooms, bedrooms, kitchens,
dining rooms, home ofices or anywhere full control of fan speed is
desired.
Compatibility:
Requires device with Bluetooth
®
4.0 (BT LE) or later and iOS 6.0 and
later. Compatible with iPhone, iPad, and iPod touch or Android 4.0 and
later.
FEATURES
• ON/OFF LED and fan ppeed level LED
• Two way communication
• Ease of installation – No new wiring
TOOLS NEEDED FOR YOUR FAN SPEED CONTROL
Slotted/Phillips Screwdriver
Electrical Tape
Pliers
Pencil
Cutters
Ruler
Changing the color of your Fan Speed Control:
Your device may include color options. To change color of the face
proceed as follows:
1
2
Push in sides at bottom
Insert top tabs and
tabs and pull outward to
press in bottom tabs
release
to attach
INSTALLING FAN SPEED CONTROL BY ITSELF OR
WITH OTHER DEVICES
If installing the Fan Speed Control in a single device application,
proceed with the INSTALLING YOUR FAN SPEED CONTROL section.
If installing Fan Speed Control in a multi-device application, proceed
as follows:
Single Pole (One location) or 3-Way (Multi-location)
MULTI-DEVICE APPLICATION
In multi-fan speed control installations, there is no derating necessary.
Refer to the chart for maximum load per fan speed control.
MAXIMUM FAN SPEED CONTROL FOR MULTI-DEVICE
Cat. No.
Single
Two Devices
More than 2 Devices
DDF01
1.5A
1.5A
1.5A
INSTALLING YOUR FAN SPEED CONTROL
NOTE: Use check boxes
when Steps are completed.
WARNING:
TO AVOID FIRE SHOCK OR DEATH; TURN
Step 1
OFF POWER at circuit breaker or fuse and test that power
is off before wiring!
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
Identifying your wiring application (most common):
Step 2
NOTE: If the wiring in your wall box does not resemble any
of these conigurations, consult an electrician.
1
2
2
1
3
3
4
5
4
3-Way
Single Pole
1. Line or Load
1. Line (Hot)
(see important
2. Neutral
instruction)
3. Ground
2. Neutral
4. Load
3. Ground
4. First Traveler – note color
5. Second Traveler – note color
Quiet Fan Speed Control
Cat. No. DDF01-BL
120VAC, 60Hz
INSTALLATION INSTRUCTIONS
WARNINGS AND CAUTIONS:
• For use on ceiling paddle fans with split-capacitor or shaded pole motors only. Please refer to manufacturer's instructions or rating label on the motor to conirm type. Use with any other
types of motors or equipment may cause overheating and/or damage to the motors or equipment.
• Use only one (1) Fan Speed Control per load. The switch(es) will turn ON the fan at the speed level selected at the control.
• To avoid overheating and possible damage to this device and other equipment, DO NOT install to control a receptacle, luorescent lighting, a motor or a transformer-operated appliance
other than appropriate ceiling fans.
INSTALLING YOUR FAN SPEED CONTROL
NOTE: Use check boxes
when Steps are completed.
WARNING:
TO AVOID FIRE SHOCK OR DEATH; TURN
Step 1
OFF POWER at circuit breaker or fuse and test that power
is off before wiring!
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
Identifying your wiring application (most common):
Step 2
NOTE: If the wiring in your wall box does not resemble any
of these conigurations, consult an electrician.
1
2
2
1
3
3
4
5
4
3-Way
Single Pole
1. Line or Load
1. Line (Hot)
(see important
2. Neutral
instruction)
3. Ground
2. Neutral
4. Load
3. Ground
4. First Traveler – note color
5. Second Traveler – note color
IMPORTANT: For 3-Way applications, note that one of the screw
terminals from the old switch being removed will usually be a different
color (Black) or labeled Common. Tag that wire with electrical tape and
identify as the common (Line or Load) in both the fan speed wall box and
remote wall box.
Preparing and connecting wires:
Step 3
Pull off pre-cut insulation from fan speed control leads. Make
sure that the ends of the wires from the wall box are straight
(cut if necessary). Remove insulation from each wire in the
wall box as shown:
5/8"
Strip Gage
(1.6 cm)
(measure bare
wire here)
Cut
(if necessary)
• Pull off pre-cut insulation from fan speed control leads.
• Make sure that the ends of the wires from the wall box are straight
(cut if necessary).
• Remove insulation from each wire in the wall box as shown.
• For Single-Pole Application, go to Step 4a.
• For 3-Way Matching Remote (w/LEDs) Application, go to Step 4b.
For non-standard wiring applications, refer
to Wire Connector and Conductor Size Chart
WIRE CONNECTOR / # OF COND.
COMBINATION CHART
1 - #12 w/ 1 to 3 #14, #16 or #18
2 - #12 w/ 1 or 2 #16 or #18
1 - #14 w/ 1 to 4 #16 or #18
2 - #14 w/ 1 to 3 #16 or #18
Single Pole Wiring Application:
Step 4a
Black
1
White
2
4
Red
3
Green
Yellow/Red
Insulating label:
This wire is used in 3-way installations only.
For single pole installations, do not remove insulating label.
Fan Speed Control
Red
Black
Hot (Black)
Black
White
Yellow/Red
Line
Green
120 VAC,
Insulating
Ground
60Hz
Label
White
Neutral (White)
WIRING FAN SPEED CONTROL:
Connect wires per WIRING DIAGRAM as follows:
NOTE: The DDF01 Fan Speed Control requires a neutral wire connection.
• Green or bare copper wire in wall box to Green fan speed control lead.
• Line Hot wall box wire to Black fan speed control lead.
• Load wall box wire to Red fan speed control lead.
• Line Neutral wall box wire to White fan speed control lead.
• Yellow/Red fan speed control lead should have Red insulation
label afixed.
NOTE: If insulating label is not afixed to Yellow/Red fan speed control
lead, use electrical tape to cover.
• Proceed to Step 5.
DI-000-DDF01-02A-X0
3-Way Wiring with DD00R Matching Remote
Step 4b
(w/LEDs) Application:
Matching Remote
Fan Speed Control
Additional Neutral Wire
Black
4
2
White
2
1
1
Red
4
3
3
5
Green
5
Yellow/Red
Matching Remote (w/LEDs)
Fan Speed Control
Hot (Black)
Black
WH
BK
Red
Green
Black
Green
Ground
Ground
White
YL/RD
Yellow/
Line
Red
120VAC, 60Hz
White
Neutral (White)
WIRING MATCHING REMOTE (wall box with line hot
connection):
Connect wires per WIRING DIAGRAM as follows:
NOTE: The matching remote must be installed in a wall box with a
Line Hot connection and a Neutral connection. A Neutral wire to the
matching remote needs to be added as shown.
NOTE: Maximum wire length from fan speed control to all installed
remotes cannot exceed 300 ft (90 m).
• Green or bare copper wire in wall box to Green terminal screw.
• Line Hot (common) wall box wire identiied (tagged) when removing
old switch and First Traveler to Remote terminal marked "BK".
• Second Traveler wall box wire from fan speed control to remote
terminal screw marked "YL/RD" (note wire color). This traveler from
the remote must go to Yellow/Red fan speed control lead.
• Line Neutral wall box to remote terminal screw marked "WH".
WIRING FAN SPEED CONTROL (wall box with load
connection):
Connect wires per WIRING DIAGRAM as follows:
NOTE: The DDF01 fan speed control must be installed in a wall box
that has a Load connection and a Neutral connection.
• Green or bare copper wire in wall box to Green fan speed control lead.
• Load wall box wire identiied (tagged) when removing old switch to
Red fan speed control lead.
• First Traveler Line Hot to Black fan speed control lead.
• Remove Red insulating label from Yellow/Red fan speed control lead.
• Second Traveler wall box wire (note color as above) to
Yellow/Red fan speed control lead. This traveler from the fan speed
control must go to the terminal screw on the remote marked "YL/RD".
• Line neutral wall box wire to White fan speed control lead.
• Proceed to Step 5.
Publicité
