Leviton decora DD710-BD Instructions D'installation

WARNINGS AND CAUTIONS:
• TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring!
• TO AVOID FIRE, PERSONAL INJURY OR PROPERTY DAMAGE, DO NOT install to control a receptacle, a motor- or a transformer-operated appliance.
• To be installed and/or used in accordance with electrical codes and regulations.
• If you are unsure about any part of these instructions, consult an electrician.
• TO AVOID FIRE, SHOCK, OR DEATH; USE ONLY WITH appropriate LED 0-10V dimmable power supplies/drivers, Advance Transformer 120/277V Mark 7
Sylvania QUICKTRONIC ® or Helios TM electronic ballasts.
• The Decora DD710 dimmer is not compatible with standard 3-way or 4-way switches. It must be used with a Decora
®
INTRODUCTION
The next generation of lighting control technology is here with the new
Decora ® Digital Dimmer with Bluetooth ® Technology. This innovative
device works using the Leviton Decora Digital Dimmer & Timer app
®
that can be easily downloaded to smartphones or tablets and paired
to the Leviton Dimmer using Bluetooth ® technology. Decora ® Digital
Devices give users point-to-point local control to automate lighting,
bridging the gap between standard dimmers and whole-house
automation systems.
The Decora ® Digital Dimmer is a powerful device – combining the best
of Leviton dimmer and timer functions with today's mobile technology
for impressive results. The simple touch of a inger following the
intuitive on-screen guide makes it more convenient than ever to
manage lighting for home activities or to ensure a "lived-in" look
while away.
Use of the app allows greater lexibility for accurate timer functionality
and makes pushing buttons for timed events a tedious chore of
the past.
The Leviton Decora ® Digital Dimmer & Timer app can be easily
downloaded to mobile devices and is compatible with Android and iOS
smartphones or tablets. The app is easy to use with simple, intuitive
on-screen menu options to independently control dimmers and
switches throughout the home.
Decora ® Digital Devices are ideal for living rooms, bedrooms, kitchens,
dining rooms, home ofices, outdoor lighting or anywhere full control of
lighting is desired.
Compatibility:
Requires device with Bluetooth ® 4.0 (BT LE) or later and iOS 6.0 and
later. Compatible with iPhone, iPad, and iPod touch or Android 4.0 and
later.
FEATURES
• Soft fade ON/OFF
• ON/OFF LED and Brightness level LED
• Three way communication
• Ease of installation – No new wiring
TOOLS NEEDED TO INSTALL YOUR DIMMER
Slotted/Phillips Screwdriver Electrical Tape Pliers
Pencil Cutters Ruler
Changing the color of your Dimmer:
Your device may include color options. To change color of the face
proceed as follows:
1
2
Push in sides at bottom Insert top tabs and
tabs and pull outward to press in bottom tabs
release to attach
Single Pole (One location) or 3-Way (Multi-location)
Cat. No. DD710-BD, 120/277V, 8A 960VA (120V), 5A 1385VA (277V)
For use with ixtures using 0-10V dimmable power supply/drivers, Advance Transformer Mark 7
OSRAM Sylvania QUICKTRONIC
Digital remote for multi-location control, such as the DD00R-DL.
®
INSTALLING DIMMER BY ITSELF
OR WITH OTHER DEVICES
If installing Dimmer in a single device application, proceed with the
INSTALLING YOUR DIMMER section. If installing Dimmer in a
multi-device application, proceed as follows:
MULTI-DEVICE APPLICATION
NOTE: No derating is required in multi-device applications.
Remove all
inner side
sections
Do not
remove
Bend back and
outer side
forth to remove
sections
side section
MAXIMUM BULB WATTAGE
0-10VDC ballasts are rated in Volt-Amps (VA). The maximum number of
ballast per dimmer is based on the load VA rating. The maximum bulb wattage
is determined by the eficiency of the ballast. Ballast eficiencies will vary from
different manufacturers; consider 80% eficient as average. Use the chart to
determine maximum bulb wattage for typical ballast eficiency ratings.
Use with Leviton's OPP20 Power Pack to increase the switch rating to 20
Amps for 120 and 277VAC ballast.
MAXIMUM BULB WATTAGE AT 75% EFFICIENCY
Rating Single Two Gang More than 2 Gang
1000VA 800W 640W 560W
Fluorescent Digital Dimmer
® , Helios TM or equivalent dimmable ballasts
INSTALLATION INSTRUCTIONS
WARNINGS AND CAUTIONS:
• Maximum wire length from dimmer to all installed remotes cannot exceed 300 ft.
• Dimmer may feel warm to the touch during normal operation.
• When retroitting dimming ballasts into ixtures that originally had Instant Start ballasts, the sockets MUST be replaced with Rapid Start sockets to allow proper dimmer operation and to
prevent damage to the dimming ballast. Refer to the instructions provided with the ballast.
® 0-10V ballasts or OSRAM
• Recommended minimum wall box depth is 2-3/4".
• Use this device WITH COPPER OR COPPER CLAD WIRE ONLY.
INSTALLING YOUR DIMMER
NOTE: Use check boxes when Steps are completed.
WARNING: TO AVOID FIRE SHOCK OR DEATH; TURN
Step 1
OFF POWER at circuit breaker or fuse and test that power
is off before wiring!
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON
OFF ON OFF ON
OFF ON OFF ON
OFF ON OFF ON
Identifying your wiring application (most common):
Step 2
NOTE: If the wiring in your wall box does not resemble any
of these conigurations, consult an electrician.
6
1 7
2 2
1
3 3
4
4
5
5
6
Single Pole 3-Way
1. Line (Hot) 1. Line or Load (see note below)
2. Neutral 2. Neutral
3. Ground 3. Ground
4. Load 4. First Traveler – note color
5. Gray (-) 5. Second Traveler – note color
6. Violet ( + )
6. Gray (-)
7. Violet ( + )
NOTE: For 3-Way applications, note that one of the screw terminals from
the old switch being removed will usually be a different color (Black) or
labeled Common. Tag that wire with electrical tape and identify as the
common (Line or Load) in both the dimmer wall box and remote wall box.
Preparing and connecting wires:
Step 3
Pull off pre-cut insulation from dimmer leads. Make sure that
the ends of the wires from the wall box are straight (cut if
necessary). Remove insulation from each wire in the wall box
as shown:
5/8"
Strip Gage
(1.6 cm)
(measure bare
wire here)
Cut
(if necessary)
• Pull off pre-cut insulation from dimmer leads.
• Make sure that the ends of the wires from the wall box are straight
(cut if necessary).
• Remove insulation from each wire in the wall box as shown.
• For Single-Pole Application, go to Step 4a.
• For 3-Way Matching Remote (w/LEDs) Application, go to Step
4b.
® ,
For non-standard wiring applications, refer
to Wire Connector and Conductor Size Chart
WIRE CONNECTOR / # OF COND.
COMBINATION CHART
1 - #12 w/ 1 to 3 #14, #16 or #18
2 - #12 w/ 1 or 2 #16 or #18
1 - #14 w/ 1 to 4 #16 or #18
2 - #14 w/ 1 to 3 #16 or #18
Single Pole Wiring Application:
Step 4a
Dimmer
Red
Dimmer
Leads
1
2
Black
Dimmer
3
Lead
4
5 Green
6
Dimmer
Lead
Gray (-)
Violet (+)
Dimmer Lead
Dimmer Lead
Wiring Diagram 1
Dimmer Hot (Black)
To Lamps
Red Black
Red
Insulating
Line
Blue Red
0-10 VDC
Label
120/277VAC
Ballast
Yellow
60Hz
Gray (-)
Violet (+)
Green
Ground
Neutral (white)
Connect wires per WIRING DIAGRAM as follows:
• Green or bare copper wall box wire to GREEN dimmer lead.
• Line Hot wall box wire to BLACK dimmer lead.
• Load wall box wire to RED dimmer lead.
• Remaining RED Dimmer lead should have a label afixed.
DO NOT REMOVE this label in a single pole application.
NOTE: If the insulating label is not afixed to the second RED lead use
electrical tape or a wire connector to cover.
• Violet dimmer lead to (+) Violet connection on ballast.
• Gray dimmer lead to (-) Gray connection on ballast.
Proceed to Step 5.
DI-000-DD710-02A-X0
3-Way Wiring with DD00R Matching Remote
Step 4b
(w/LEDs) Application:
Dimmer Red 3-Way
Dimmer
Leads
1
2 3 2
Black
Dimmer
3
Lead
4
4
5 5
6 Green 1
7
Dimmer
Lead
Black
Screw
Gray (-)
(common)
Dimmer Lead Violet (+)
Dimmer Lead
Wiring Diagram 2
3-Way Dimmer Hot (Black)
To Lamps
Red Black
Red
Red
Black Screw
Blue 0-10 VDC
Line
(common)
Ballast
Yellow 120/277VAC
60Hz
Green
Ground
Green
Ground
Gray (-)
Violet (+)
Neutral (white)
Connect wires per WIRING DIAGRAM as follows:
• Green or bare copper wall box wire to GREEN dimmer lead.
• Common (Line hot or Load) wire to BLACK dimmer lead.
• Remove insulating label and connect the irst traveler wire to the
RED dimmer lead.
• Connect the second traveler wire to the remaining RED dimmer
lead.
• VIOLET dimmer lead to (+) Violet connection on ballast.
• GRAY dimmer lead to (-) Gray connection on ballast.
Proceed to Step 5.