Bosch PIE84KBB5E Notice D'installation page 10

Installation above an oven
¡ To ensure good ventilation, the clearance between
the top of the worktop and the surface of the oven
front must be 30 mm and the minimum clearance
between the oven and hob must be 5 mm.
¡ If the clearance between the hob and the oven
needs to be increased, refer to the installation in-
structions for the oven.
→ Fig.
7
Installing the power cord in the mains
socket
Requirement: For appliances without a preinstalled
power supply.
Turn the hob over and put it down on the base of
1.
the packaging, a cloth or another surface in order
to prevent scratches.
→ Fig.
8
Use a screwdriver to lift up the cover of the mains
2.
socket.
→ Fig.
9
Undo the fastening screw and use a screwdriver
3.
to lift the hose clamp.
→ Fig.
10
Only connect to the mains socket as shown in the
4.
figure:
→ Fig.
11
– BN: Brown
– BU: Blue
– GN/YE: Green and yellow
– BK: Black
– GY: Grey
Note: If you implement the connection in accord-
ance with connection diagram 2L/2N, you must
change the configuration of the bridges in accord-
ance with the diagram.
After connecting the cable, tighten the screws on
5.
the mains socket correctly.
Use the hose clamp to secure the power cord and
6.
tighten the fastening screw.
→ Fig.
12
Route the cables into the central area of the mains
7.
socket. Close the cover on the socket.
If the power cord gets in the way of the drawer,
8.
use the enclosed cable tie to secure the cable to
the underside of the hob.
→ Fig.
13
Installing the support rails
Install the support rails in the unit.
▶
Glue the support rails to the stone worktop. Use
‒
a melt adhesive that is suitable for bonding
metal and stone and has a temperature resist-
ance of at least 90 °C.
Do not use silicone for sealing.
‒
If mounting rails have already been attached,
‒
remove these and attach new ones.
Use the lower threaded holes for tiled work sur-
‒
faces.
→ Fig.
14
Inserting the hob
Insert the hob in the cut-out.
1.
→ Fig.
15
Place the appliance into the cut-out in the worktop.
2.
Screw the enclosed retaining clips onto the
‒
worktop and carefully onto the appliance.
Do not use an electric screwdriver.
‒
→ Fig.
16
Seal the tile joints on tiled work surfaces with silic-
3.
one rubber.
10
Note: Do not kink or trap the connection cable, and
keep it away from sharp edges and hot parts.
Connecting the appliance
Requirement: Observe the connection data on the
rating plate.
Only connect as shown in the circuit diagram:
1.
→ Fig. , → Fig.
17 18
– BN: Brown
– BU: Blue
– GN/YE: Green and yellow
– BK: Black
– GY: Grey
Note: Depending on the type of connection, you
may have to change the arrangement of the ter-
minals supplied by the factory. For this, you may
have to shorten the clamps and remove the insu-
lation in order to insert a clamp that connects the
two cables.
Check that the appliance is ready for operation: If
2.
, or appears on the appliance's dis-
play, the appliance is not connected correctly. Dis-
connect the appliance from the power supply and
check the power cord connection at the mains
supply.
Special combinations
If you install the hob above an oven made by an-
other brand, use a wooden partition floor.
→ Fig.
19
Removing the appliance
ATTENTION!
Tools may damage the appliance.
Never prise out the appliance from above.
▶
Disconnect the appliance from the mains power
1.
supply.
If there are any fastening brackets, remove them.
2.
Push out the hob from below.
3.
fr
Indications générales
¡ Lisez attentivement cette notice.
¡ Seul un spécialiste agréé est autorisé à
brancher l'appareil.
¡ Une installation, une ouverture de l'appa-
reil, un raccordement ou un montage in-
corrects annulent la validité de la garantie
du produit.
¡ Avant toute intervention sur l'appareil,
coupez l'alimentation électrique.
¡ Après l'installation, s'assurer que l'utilisa-
teur n'a aucun accès aux pièces élec-
triques.
¡ N'utilisez jamais cet appareil dans un ba-
teau ou un véhicule.