Continental Fireplaces CBLP42 Manuel Du Propriétaire page 10

If the appliance is equipped with a CPI/IPI toggle switch, set the CPI/IPI
to CPI position to enable remote CPI operation. If the switch is set to IPI
then it will only work in IPI regardless of what is set on the remote control
remote control layout
EN
handset.
3.8 low battery
ADD TITLE: LOW BATTERY / MANUAL BYPASS
The life span of the remote batteries depends on various factors: quality of the batteries,
the number of ignitions, etc.
When the transmitter batteries are low, a battery icon will appear on the LCD display
before all battery power is lost. When the batteries are replaced, this icon will disappear.
When the receiver batteries are low, no "beep" will be emitted from the receiver when
it receives an on/off command. This in an alert for the receiver that there's low battery.
When the batteries are replaced the "beep" will be emitted from the receiver when the on/off key is pressed.
If the batteries of the receiver or transmitter are low, the appliance can be turned on manually by sliding the
three position slider switch on the receiver to the on position. This will bypass the remote control feature and the
appliance main burner will come on if the gas valve is in the on position.
ADD TITLE: IN THE EVENT OF A POWER FAILURE
3.9 battery holder / backup installation
If the receiver is equipped with batteries they will enable fl ame height control or on/off function to control the
appliance during a power failure. Blower and Night Light™ operation is not possible. Refer to "appliance
A. The battery holder is located in the valve compartment,
operation" section when communications between receiver and transmitter have been lost. The receiver will
emit a "beep" sound to confi rm programming has been successful once power is restored. During a power
accessible for programming the remote.
failure, if the appliance was on, the fl ame height will stay at the setting prior to the failure. If off when the failure
occurs and then turned on, the fl ame height will come on at "Hi". The fl ame height can then be controlled by the
B. Install 4 AA batteries, Ensure that the positive and negative
remote.
ends correspond with those identified in the battery holder.
C. In the case of a power outage, the 3 position slider switch
needs to be in the "ON" position (left).
note:
Ensure the 3 positions slider switch is in the "REMOTE"
position (middle).
10
W415-4064 / 04.19.22
OFF
Flame Off
MAX
76
child lock
OFF
73
73
Flame Off
child lock
Room Temperature
Room Temperature
68
ON
68
ON
Set Temperature
Set Temperature
SMART
SMART
MAX
76
MAX
76
OFF
OFF
Flame Off
Flame Off
child lock
child lock
Blue LCD Display
Temperature Key
On / Off Key
Up / Down Arrow Key
Temperature Key
Flame at level 1
Up / Down Arrow Key
76
Mode Key
°F
76
Mode Key
°F °F
23
°F °C
23
°F °C
Flame at level 1
76
°F
76
°F
76
°F
76
°F
76
°F
76
RESET/PROGRAM BUTTON (PRG)
°F °F
76
°F °F
Flame at level 1
76
Flame at level 1
°F
76
°F
OFF ON
Hi
76
OFF
Flame at level 5 Flame at "Hi" level 6
76 76
°F
76
IPI CPI
76 76
°F
76
Hi
Flame at level 5 Flame at "Hi" level 6
76 76
76
°F
°F
IPI CPI
68
76
°F
68
76
°F
OFF
76
°F
OFF
76
°F
76
°F
Flame at level 5 Flame at "Hi" level 6
76
23.3
Flame at level 5 Flame at "Hi" level 6
°F
IPI CPI
76
°F
IPI CPI
76
ON
°F
°F
°F
°F
76
°F
°F
Hi
76
°F
Hi
76
°F
76
°F
76
°F
76
Hi
°F
Hi
76
°F
76
°F