Service Information - DeWalt DHS716 Guide D'utilisation

Clamp: DW7082 Used for firmly clamping
workpiece to the saw
table for precision cutting.
Dust Bag: Equipped with a zipper
DW7053 for easy emptying, the
(included with dust bag will capture the
some models) majority of the sawdust
produced.
Crown Molding Used for precision cutting
Fence: DW7084 of crown molding.
Kerf Plate Blank: DW7055 (not shown)
Used to limit back side tear out of material or as a replacement kerf plate.
SAW BLADES: ALWAYS USE 12" (305 mm) SAW BLADES WITH EITHER 1" (25.4 mm) OR
5/8" (15.88 mm) ARBOR HOLES. SPEED RATING MUST BE AT LEAST 4800 RPM. Never
use a smaller diameter blade. It will not be guarded properly. Use crosscut blades only!
Do not use blades designed for ripping, combination blades or blades with hook angles in
excess of 7°.
BLADE DESCRIPTIONS
APPLICATION
Construction Saw Blades (thin kerf with anti-stick rim)
General Purpose
Fine Crosscuts
Woodworking Saw Blades (provide smooth, clean cuts)
Fine crosscuts
Non-ferrous metals
NOTE: For cutting non-ferrous metals, use only saw blades with
TCG (Triple Chip Grind) teeth designed for this purpose.
DIAMETER TEETH
12" (305 mm) 40
12" (305 mm) 60
12" (305 mm) 80
12" (305 mm) 96
Repairs
The charger, power supply and battery pack are not serviceable. There are no serviceable parts
inside the charger, power supply and battery pack.
WARNING: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment (including brush inspection and replacement) should be performed by a
D WALT factory service center or a D
e
replacement parts.

Service Information

Please have the following information available for all service calls:
Model Number __________________ Serial Number __________________________________
Date and Place of Purchase _______________________________________________________
Register Online
Thank you for your purchase. Register your product now for:
• WARRANTY SERVICE: Registering your product will help you obtain more efficient
warranty service in case there is a problem with your product.
• CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or
theft, your registration of ownership will serve as your proof of purchase.
• FOR YOUR SAFETY: Registering your product will allow us to contact you in the
unlikely event a safety notification is required under the Federal Consumer Safety Act.
Register online at www.dewalt.com/register.
Three Year Limited Warranty
D WALT will repair, without charge, any defects due to faulty materials or workmanship for
e
three years from the date of purchase. This warranty does not cover part failure due to normal
wear or tool abuse. For further detail of warranty coverage and warranty repair information,
visit www.dewalt.com or call 1-800-4-D
apply to accessories or damage caused where repairs have been made or attempted by
others. This warranty gives you specific legal rights and you may have other rights which vary
in certain states or provinces.
In addition to the warranty, D WALT tools are covered by our:
e
1 YEAR FREE SERVICE
D WALT will maintain the tool and replace worn parts caused by normal use, for free, any time
e
during the first year after purchase.
2 YEARS FREE SERVICE ON D
DC9071, DC9091, DC9096, DC9182, DC9280, DC9360,
DCB120, DCB127, DCB201, DCB203, DCB203BT, DCB207, DCB361
3 YEARS FREE SERVICE ON D
DCB200, DCB204, DCB204BT, DCB205, DCB606
D WALT BATTERY PACKS
e
Product warranty voided if the battery pack is tampered with in any way. D
responsible for any injury caused by tampering and may prosecute warranty fraud to the
fullest extent permitted by law.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of your D
Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt
for a full refund – no questions asked.
19
WALT authorized service center. Always use identical
e
WALT (1-800-433-9258). This warranty does not
e
WALT BATTERY PACKS
e
WALT BATTERY PACKS
e
e
WALT Power Tool, Laser, or
e
WALT is not