Radio Operation - Milwaukee M12 Manuel De L'utilisateur

RADIO ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.
The MILWAUKEE M12 ™ Radio + Charger can be
powered by MILWAUKEE M12™ Li-Ion battery packs
or a standard wall outlet. When plugged into a wall
outlet, the battery bay will charge MILWAUKEE
M12™ Li-Ion battery packs (see Charger Operation).
Inserting/Removing Battery Pack
1. To insert the battery pack, slide it into the battery
bay.
2. To remove the battery pack, pull the battery pack
off of the bay.
Low Battery Indicator
When the radio is powered by a battery pack and
its charge falls below 10%, the low battery indicator
is displayed.
Battery Pack Protection
To protect the life of the battery pack, the radio will
shut off when the battery's charge becomes too low.
If this happens, plug Radio + Charger into a 120V
outlet and charge the battery pack according to
Charger Operation.
USB Power Outlet
This outlet can be used to charge a cell phone, power
an MP3 player or any other device that uses less than
2.1 A of DC electrical current.
NOTE: Any device that uses more than 2.1 A of DC
electrical current will trip a self-resetting overload
and disable the output.

RADIO OPERATION

Always remove battery pack before
WARNING
changing or removing accesso-
ries. Only use accessories specifically recom-
mended for this radio. Others may be hazardous.
To reduce the risk of fire or electric shock, do not
expose this radio to rain or moisture.
Turning On/Off and Controlling Volume
Plug the cord into an appropriate AC outlet or install
a battery pack.
Press and hold the On/Off button
turns ON or OFF. The radio station (frequency) is
displayed. To display the time, press the CLOCK
button. Volume is restored to the last setting.
NOTE: When the Radio + Charger is running on
battery power, the display will dim after 5 minutes to
reduce power use.
Use the Volume up and down buttons to increase or
decrease the volume.
Power
until the radio
Setting the Clock
1. Press and hold the CLOCK button until the hour
begins to flash.
2. Use the ◄ and ► buttons to change the hour.
3. Press the CLOCK button again. The minutes will
begin to flash. Use the ◄ and ► buttons to change
the minutes.
4. Press the CLOCK button again to save.
EQ Adjustment
Press and hold the AM/FM button to enter tuning
mode. Use the ◄ and ► buttons or
buttons to adjust Treble, and then Bass.
Selecting Band
Push the AM/FM button to select AM or FM
Tuning and Seeking
Press the ◄ and ► buttons to move up and down
the band. Press, hold, and release the ◄ and ►
buttons to SEEK through the band. When a station
is found, the SEEK will stop.
PRESET Stations
To set the PRESET stations:
1. Tune to desired station.
2. Press and hold the PRESET button until the PRE-
SET indicator on the display begins to flash.
3. Use the ◄ and ► buttons to select the PRESET
location for the station. Five locations (1-5) are
available for both AM and FM.
4. Press the PRESET button to save the location.
To tune to a PRESET station:
Press and release the PRESET button to step
through the PRESET stations.
Using Bluetooth
To enter the Bluetooth mode, press the
• If no Bluetooth device is connected, Bluetooth
pairing will begin automatically and the
flash on the display.
• The radio will continue to search for a signal for
3 minutes.
• While the is flashing, select "M12 Radio +
Charger" on the Bluetooth capable device.
• Once the device has successfully paired with the
radio, the will be shown on the radio's display.
Connecting
To enter the Bluetooth mode, press the
When the radio locates a paired Bluetooth device,
the will stop flashing.
If connection is lost between the radio and the Blue-
tooth device, the radio will try to reconnect automati-
cally for up to 3 minutes.
Controlling
When streaming music through to the radio via a
Bluetooth device, use the
► to move through the tracks.
5
Pairing
button. Use the ◄ and
and
button.
icon will
button.