Milwaukee V 28 H Instructions D'utilisation page 15

TECHNICAL DATA
Drilling capacity in concrete ..............................................................
Drilling capacity in steel ....................................................................
Drilling capacity in wood ...................................................................
Light core cutter in bricks and limestone ..........................................
No-load speed ..................................................................................
Single impact strength ......................................................................
Chuck neck diameter ........................................................................
battery ..............................................................................................
Battery voltage .................................................................................
Weight with battery ...........................................................................
Typical A-weighted sound levels:
Sound pressure level ....................................................................
Sound power level .........................................................................
Typical weighted acceleration in the hand-arm area ........................
Measured values determined according to EN 60 745.
SAFETY INSTRUCTIONS
Please pay attention to the safety instructions in the attached
leaflet!
Wear ear protectors. Exposure to noise can cause hearing loss.
Use auxiliary handles supplied with the tool. Loss of control
can cause personal injury.
Always wear goggles when using the machine. It is recommended
to wear gloves, sturdy non slipping shoes and apron.
Sawdust and splinters must not be removed while the machine is
running.
When working in walls ceiling, or floor, take care to avoid electric
cables and gas or waterpipes.
The dust that arises when working with this tool can be
detrimental to health and therefore not reach the body. Wear a
suitable dust protection mask.
Remove the battery pack before starting any work on the
machine.
Do not dispose of used battery packs in the household refuse or
by burning them. Milwaukee Distributors offer to retrieve old
batteries to protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
Use only System V 28 chargers for charging System V 28 battery
packs. Do not use battery packs from other systems.
No metal parts must be allowed to enter the battery section of the
charger (short circuit risk).
Never break open battery packs and chargers and store only in
dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load
or extreme temperatures. In case of contact with battery acid
wash it off immediately with soap and water. In case of eye
contact rinse thoroughly for at least 10 minutes and immediately
seek medical attention.
SPECIFIED CONDITIONS OF USE
The battery rotary pneumatic hammer can be used for hammer
drilling and drilling in wood, metal as well as plastic for
independent use away from mains supply.
Do not use this product in any other way as stated for normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in
conformity with the following standards or standardized
documents. EN 60745, EN 55014-1, EN 55014-2, in accordance
with the regulations 98/37/EEC, 89/336/EEC
Manager Product Development
17 ENGLISH
Volker Siegle
V 28 H V 28 HX
............ 26 mm ...................... 26 mm
............ 13 mm ...................... 13 mm
............ 30 mm ...................... 30 mm
............ 68 mm ...................... 68 mm
........ 1400 min ................. 1400 min
-1
........... 3,2 J ......................... 3,2 J
............ 54 mm ...................... 54 mm
....... Li-Ion ....................... Li-Ion
............ 28 V ..................... 28 V
........... 4,1 kg ....................... 4,3 kg
............ 94 dB (A) .................. 94 dB (A)
.......... 105 dB (A) ................ 105 dB (A)
............ 12 m/s ..................... 12 m/s
2
BATTERIES
Please take note of the specific information relating to Milwaukee
28V rechargeable batteries in the instruction manual for the
charger.
New battery packs reach full loading capacity after 4 - 5 chargings
and dischargings. Battery packs which have not been used for
some time should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance
of the battery pack. Avoid extended exposure to heat or sunshine
(risk of overheating).
The contacts of chargers and battery packs must be kept clean.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
Important note! If the carbon brushes are worn, in addition to
exchanging the brushes the tool should be sent to after-sales
service. This will ensure long service life and top performance.
Use only Milwaukee accessories and Milwaukee spare parts.
Should components need to be replaced which have not been
described, please contact one of our Milwaukee service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the Article No. as well as the machine type printed on the
label and order the drawing at your local service agents or directly
at: Milwaukee Electric Tool, Max-Eyth-Straße 10,
D-71364 Winnenden, Germany.
SYMBOLS
Accessory - Not included in standard equipment,
available as an accessory.
Always disconnect the plug from the socket before
carrying out any work on the machine.
Do not dispose of electric tools together with
household waste material! In observance of
European Directive 2002/96/EC on waste electrical
and electronic equipment and its implementation in
accordance with national law, electric tools that
have reached the end of their life must be collected
separately and returned to an environmentally
compatible recycling facility.
-1
2