Page 1
INSTRUCTION MANUAL - GUIDE D’INSTALLATION N005 SHOWER DOOR - PORTE DE DOUCHE 2 PEOPLE REQUIRED 2 PERSONNES REQUIS IT IS MANDATORY TO HAVE A WALL STUD ON EACH SIDE OF THE SHOWER UNIT TO SECURELY FASTEN THE RAIL TO THE WALLS. IL EST OBLIGATOIRE D’AVOIR UNE OSSATURE MURALE SUR CHAQUE CÔTÉ...
INSTRUCTION MANUAL - GUIDE D’INSTALLATION GENERAL INSTRUCTIONS • Read this manual carefully and completely before proceeding. • It is recommended that you wear safety glasses at all times during the installation. INSTALLATION OVER CERAMIC TILES • If your shower door is to be installed over ceramic tiles, the tiles should lie completely under the wall jamb. •...
Page 4
PARTS LISTING / LISTE DES PIÈCES All models EXCEPT NOV148. This part illustrated in manual. For model NOV148 ONLY. Pour tous les modèles SAUF NOV148. Pour le modèle NOV148 UNIQUEMENT. Cette pièce est illustrée dans le manuel. ITEM PARTS - PIÈCES WALL JAMB / JAMBAGE EXPANDER / EXTENSEUR EXPANDER GASKET / JOINT DE L’EXTENSEUR...
Page 5
“B” dimensions that relate to your model. MODEL OUVERTURE DU DEVANT OUVERTURE DU CÔTÉ MODÈLE Measure and mark the previously deter- mined minumum and maximum dimensions NOV24836-CRP 45" 46" 33" 33 5/8" on the threshold of the base. The set points indicate the recommended position for the NOV26036-CRP 57"...
Page 6
INSTRUCTION MANUAL - GUIDE D’INSTALLATION DOOR PANEL ASSEMBLY / ASSEMBLAGE DE LA PORTE COULISSANTE Use a mallet to install the bottom gasket (7) on the bottom of the door panel (9). To facilitate the installation, place the door panel on the cardboard packaging box and use it as platform. Notice the holes are situated at the top of the panel.
Page 7
INSTRUCTION MANUAL - GUIDE D’INSTALLATION WALL JAMB INSTALLATION / INSTALLATION DU JAMBAGE Center the wall jambs on the line marked previously on the threshold in the recommended area for the shower door instalation and align them using a level. Mark the four holes for both walls. Remove the wall jambs.
Page 8
INSTRUCTION MANUAL - GUIDE D’INSTALLATION WALL JAMB INSTALLATION / INSTALLATION DU JAMBAGE Insert one drop of silicone in each wall hole before inserting the wall plug. (x8) Apply silicone at the bottom of both wall jambs on the side that goes against the wall as illustrated. (x2) Reposition the wall jambs on the line previously marked. En- sure verticality with the level.
Page 9
INSTRUCTION MANUAL - GUIDE D’INSTALLATION WALL JAMB INSTALLATION / INSTALLATION DU JAMBAGE Place “U”-channels temporarily on the bottom of the fixed panel (10) and return panel (28). Slide the fixed panel and the pre-assembled return panel with expander (2) and gasket (3) into the wall jambs (1). Level the glass panel assembly with the wall jamb. Lock into position by clamping the wall jamb and expander with pliers. Positionnez temporairement les rails inférieurs sur la partie inférieure du panneau fixe (10) et du panneau de retour (28). Glissez le panneau fixe (10) et le panneau de retour prémontré de l’extenseur(2)et du joint (3) dans le jambage (1). Assurer le niveau du panneau fixe à l’aide d’un niveau. Barrer la position du jambage et de l’extenseur à l’aide de pinces autobloquantes. COVER THE PLIER’S TEETH BEFOREHAND TO AVOID SCRATCHING THE ALUMINUM PARTS. RECOUVREZ LES DENTS DE LA PINCE AFIN DE NE PAS GRAFIGNER LES PIÈCES EN ALUMINIUM.
Page 10
INSTRUCTION MANUAL - GUIDE D’INSTALLATION RUNNING RAIL INSTALLATION / INSTALLATION DE LA BARRE DE ROULEMENT Unfasten the set screws (x4) from the wall bracket (13) and glass mount bracket (29). Then remove the back plate from the wall bracket and set aside. Slide the wall brackets away from the ends of the running rail (12). Align running rail holes with holes in the fixed panel. Install the glass fasteners (14) to join the fixed panel (10) and rail (12). Be sure to place the gaskets between all contact with the glass and metal parts. Fasten with 3mm hex key.
Page 11
INSTRUCTION MANUAL - GUIDE D’INSTALLATION RUNNING RAIL INSTALLATION / INSTALLATION DE LA BARRE DE ROULEMENT Install the glass mount bracket. Push wall brackets against the wall, fasten the bracket on the return panel and level. Trace outer edge of the wall bracket. Trace “U”-channel locations.
Page 12
INSTRUCTION MANUAL - GUIDE D’INSTALLATION WALL BRACKET BACK PLATE / PLAQUETTE INTÉRIEURE DU SUPPORT MURAL Align the back plate of the wall bracket to the pre- viously traced mark on the wall. Mark the center of each hole to determine the drilling location. (x2) Drill the marked holes using a 1/4" drill bit. Insert a drop of silicone in each hole before insert- ing the wall plugs.
Page 13
INSTRUCTION MANUAL - GUIDE D’INSTALLATION BOTTOM GUIDE / GUIDE DU BAS Place the door panel (9) inside the shower to simplify the following installation procedures. place the panel on a cushioned surface, such as a towel or cardboard, to prevent damage to either the panel or the base.
Page 14
INSTRUCTION MANUAL - GUIDE D’INSTALLATION PANNEL INSTALLATION / INSTALLATION DES PANNEAUX Reinstall the fixed panel and return panel. Be sure to level the panels and align the fixed panel edge with the end of the bottom guide. Lock into position by clamping the wall jambs and expanders with pliers.
Page 15
INSTRUCTION MANUAL - GUIDE D’INSTALLATION RUNNING RAIL / BARRE DE ROULEMENT With the back plate previsouly secured to the wall, push the wall brackets towards the wall and lock it in. Repeat on the opposite side with the glass bracket. Tighten the set screws to secure in place with the allen key provided.
Page 16
INSTRUCTION MANUAL - GUIDE D’INSTALLATION WALL JAMB AND EXPANDER / JAMBAGE ET EXTENSEUR Drill through the wall jamb holes with a 1/8" drill bit to pierce through the expander. (x3) Screw 3/4" screws (21) through the holes to hold the expander and wall jamb together in place. (x3) Cover all the screws with screw caps (24). Percer l’extenseur à...
Page 17
INSTRUCTION MANUAL - GUIDE D’INSTALLATION 12 DOOR GASKETS / JOINT DE PANNEAU DE PORTE Temporarily install the midgasket (5) and the door gasket (6) to the door panel. Close the door entirely and mark the interfer- ence of the gaskets with the running rail. Cut the gasket at the marked locations with cutters.
Page 18
INSTRUCTION MANUAL - GUIDE D’INSTALLATION ANTI-JUMP & DOOR STOPPER / ANTI-SAUT & BUTOIR Install the anti-jump (16) in the lower holes of the door panel located below the running rail. Be sure to place the gaskets in between the glass and aluminum parts. (x2) Install the door stopper (15) located in the interior of the shower INTERIOR SHOWER SIDE next to the wall jamb. Use the hole provided in the running rail,...
Page 19
INSTRUCTION MANUAL - GUIDE D’INSTALLATION DOOR RECEIVER INTALLATION / INSTALLATION RÉCEPTRICE DE PORTE Place the door receiver (18) against the wall so that the door panel slides smoothly into the receiver. Mark the location of the hole. Remove the door receiver and drill in the marked location with a 1/8"...
Page 20
INSTRUCTION MANUAL - GUIDE D’INSTALLATION SEALING / CALFEUTRAGE Silicone the outside of the shower unit along the wall jamb and the exterior side of aluminum threshold and “U”-channel. Wait 24 hours before using the shower to allow silicone to dry. Calfeutrer l’extérieur de l’unité avec du silicone autour du jambage et à l’extérieur du seuil en aluminium et du profilé “U” en aluminium. Attendre 24 heures avant de faire fonctionner la douche afin que le silicone sèche. HEURES HOURS...