Silverline 300W Mode D'emploi page 6

EN
Introduction
Thank you for purchasing this Silverline product. This manual contains information necessary
for safe and effective operation of this product. This product has unique features and, even
if you are familiar with similar products, it is necessary to read this manual carefully to
ensure you fully understand the instructions. Ensure all users of the product read and fully
understand this manual.
Description of Symbols
The rating plate on your tool may show symbols. These represent important information about the
product or instructions on its use.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
Wear head protection.
Wear hand protection.
Read instruction manual.
Conforms to relevant legislation and safety standards.
Toxic fumes or gases!
Dust extraction required or recommended
Class II construction (double insulated for additional protection)
Environmental Protection
Waste electrical products should not be disposed of with household waste. Please
recycle where facilities exist. Check with your local authority or retailer for recycling
advice.
6
430787_OwnerManual_SEPT.indd 6 430787_OwnerManual_SEPT.indd 6
Original Instructions
Technical Abbreviations Key
V Volts
~, AC
Alternating current
A, mA Ampere, milli-Amp
n0 No load speed
opm Orbits or oscillations per minute
Degrees
°
Ø
Diameter
W, kW
Watt, kilowatt
/min or min Operations per minute
-1
dB(A) Decibel sound level (A weighted)
Specification
Voltage: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V~, 50Hz
Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300W
No load speed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15,000-23,000min
Oscillating angle:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3°
Protection class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions (L x W x H):. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 x 60 x 95mm
Power Cord Length: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8m
Ingress protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .IP20
Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.4kg
As part of our ongoing product development, specifications of Silverline
products may alter without notice.
Sound & vibration information
Sound pressure L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90.4dB(A)
PA
Sound power L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101.4dB(A)
WA
Uncertainty K . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3dB(A)
The sound intensity level for the operator may exceed 85dB(A) and
sound protection measure are necessary.
WARNING: Always wear ear protection where the sound level exceeds 85dB(A) and limit
the time of exposure if necessary. If sound levels are uncomfortable, even with ear protection, stop
using the tool immediately and check the ear protection is correctly fitted and provides the correct
level of sound attenuation for the level of sound produced by your tool.
WARNING: User exposure to tool vibration can result in loss of sense of touch, numbness,
tingling and reduced ability to grip. Long-term exposure can lead to a chronic condition. If necessary,
limit the length of time exposed to vibration and use anti-vibration gloves. Do not operate the tool
with hands below a normal comfortable temperature, as vibration will have a greater effect. Use the
figures provided in the specification relating to vibration to calculate the duration and frequency
of operating the tool.
Sound and vibration levels in the specification are determined according to international standards.
The figures represent normal use for the tool in normal working conditions. A poorly maintained,
incorrectly assembled, or misused tool, may produce increased levels of noise and vibration.
www.osha.europa.eu provides information on sound and vibration levels in the workplace that
may be useful to domestic users who use tools for long periods of time.
The declared vibration total value has been measured in accordance with a standard test method
and may be used for comparing one tool with another. The declared vibration total value may also
be used in a preliminary assessment of exposure..
WARNING: The vibration emission during actual use of the power tool can differ from the
declared total value depending on the ways in which the tool is used. There is the need to identify
safety measures to protect the operator that are based on an estimation of exposure in the actual
conditions of use (taking account of all parts of the operating cycle such as the times when the tool
is switched off and when it is running idle in addition to the trigger time).
-1
02/09/2021 17:10 02/09/2021 17:10