Bosch GWS 18V-10 Professional Notice Originale page 26

26 | English
Angle grinder
Permitted ambient temper-
D)
ature during operation
and during storage
Recommended re-
chargeable batteries
Recommended chargers
A) Rated no-load speed for the selection of appropriate application tools in accordance with EN IEC 62841-2-3. The actual no-load speed
must not exceed the rated no-load speed and is therefore lower.
B) Measured at 20–25 °C with rechargeable battery ProCORE18V 8.0Ah and depending on the battery's state of charge as well as the power
tool's operating temperature
C) Depends on rechargeable battery (5), protective guard ((13), (12), (14)) and auxiliary handle ((8), (7)) in use
D) Limited performance at temperatures < 0 °C
Values can vary depending upon the product and are subject to application and environmental conditions. For further information
www.bosch-professional.com/wac.
Noise/Vibration Information
Noise emission values determined according to EN IEC 62841-2-3.
Typically, the A-weighted noise level of the power tool is
Sound pressure level
Sound power level
Uncertainty K
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K determined according to EN IEC 62841-2-3:
h
Grinding surfaces (roughing) and abrasive cutting:
a
h
K
Disc sanding:
a
h
K
Grinding thin metal sheets or other materials that tend to easily vibrate with a large surface area can cause the noise emission value to increase by
up to 15 dB. Suitable, heavy damping mats can reduce the increased noise emissions. Increased noise emissions must be taken into considera-
tion, both for the risk assessment of the noise output and for selecting suitable hearing protection.
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ac-
cessories or is poorly maintained, the vibration level and
noise emission value may differ. This may significantly in-
crease the vibration and noise emissions over the total work-
ing period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
1 609 92A 8XF | (03.08.2023)
GWS 18V-10 GWS 18V-10
°C –20 to +50 –20 to +50
GBA 18V... GBA 18V...
≥ 4.0 Ah ≥ 4.0 Ah
ProCORE18V... ProCORE18V...
GAL 18... GAL 18...
GAX 18... GAX 18...
GAL 36... GAL 36...
GWS 18V-10 GWS 18V-10
3 601 JJ4 0.. 3 601 JJ4 0..
dB(A) 85
dB(A)
93
dB
3
2
m/s 4.7
2
m/s 1.5
2
m/s 4.1
2
m/s
1.5
GWS 18V-10 GWS 18V-10 P GWS 18V-10 P
–20 to +50 –20 to +50
GBA 18V... GBA 18V...
≥ 4.0 Ah
ProCORE18V... ProCORE18V...
GAL 18...
GAX 18...
GAL 36...
GWS 18V-10 GWS 18V-10 P GWS 18V-10 P
3 601 JJ4 0.. 3 601 JJ4 1B.
85 85
93 93
3 3
4.7 4.7
1.5 1.5
4.1 4.1
1.5 1.5
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and accessories, keeping their hands warm, and
organising workflows correctly.
Kickback stop
If there is a sudden kickback in the power tool,
e.g. jamming in a separating cut, the power
supply to the motor will be interrupted elec-
tronically.
–20 to +50
GBA 18V...
≥ 4.0 Ah ≥ 4.0 Ah
ProCORE18V...
GAL 18... GAL 18...
GAX 18... GAX 18...
GAL 36... GAL 36...
3 601 JJ4 1..
85 85
93 93
3 3
4.7 4.7
1.5 1.5
4.1 4.1
1.5 1.5
Bosch Power Tools