Multiplex Cularis S-BEC Manuel D'instructions page 4

! These operating instructions are an integral part of the
product. They contain important information and safety
notes, and should be kept in a safe place at all times. Be
sure to pass them on to the new owner if you ever dispose
of the product.
1. I
NTRODUCTION
When used with the recommended flight battery, our
power set "Cularis S-BEC" is capable of propelling the
Cularis or any similar glider to a good starting height for
extended thermal flights. It will do this six to eight times
on a single charge. If you use the MULTIcont BL-40 S-
BEC speed controller supplied in the set, you do not
require a receiver battery despite the fact that the model
contains six servos.
2. C / R
ONTENTS
• 1 Himax C 3522-0700
• 1 MULTIcont BL-40 S-BEC speed controller
• 1 propeller driver, blade holder
and spinner Ø 55 mm
• 2 folding propeller blades, 12" x 6"
• Various small items for installation in the model
3. T . O
YP PERATIONAL
S "CULARIS S-BEC"
ET
3S LiPo / 12" x 6" prop
Recommended flight battery:
MULTIPLEX Li-BATT BX 3/1-2100
MULTIPLEX Li-BATT BX 3/1-2500
MULTIPLEX Li-BATT eco 3/1-2000
MULTIPLEX Li-BATT eco 3/1-3000
Do not use the supplied Himax C 3522-0700 motor with
more than 3S LiPo or 9 NiXX cells when using the
recommended propellers.
4. S N
AFETY OTES
The power set "Cularis S-BEC" is designed exclusively for
use in modelling applications. Incorrect use can result in
serious personal injury.
• Read the instructions before initiation
• Before every flight, check that the motor and propeller
are securely mounted
• Remove all movable objects from the area around the
propeller before switching the motor on
• Do not allow clothing or any of your extremities to get
close to the spinning propeller
• Never start running the motor in your hand
• Stop the motor immediately if you notice vibration.
Eliminate the cause of the vibration before running it
again; you may need to correct the balance of the
propeller blades
• Make sure the power system is adequately cooled; do
not allow anything to obstruct the free circulation of air
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de
www.modellmarkt24.ch www.modellmarkt24.ch
All manuals and user guides at all-guides.com
Ope ra t ing I nst ruc t ions for Pow e r Se t "Cula ris S-BEC"
EPLACEMENT PARTS
D P
ATA OF OWER
Current drain: approx. 22.0 A
5. A
SSEMBLING
"C
ULARIS
Spinner
# 33 3025
# 7 2285
1. Screw the motor to the motor mount
# 73 3183 motor is free to rotate. When deploying the motor
# 73 3173 cables, check that they cannot make contact with the
spinning motor.
2. Fit the propeller driver and the hexagon driver nut on
the motor shaft.
3. Attach the folding propeller blades to the blade holder
using the screws and self-locking nuts supplied. Ensure
that the propeller blades are free to swivel to and fro.
4. Fit the blade holder with propeller blades assembled on
the propeller driver, and secure it with the spacer, the
# 15 7131
plain washer, the shakeproof washer and the hexagon
# 15 7191
nut.
# 15 7231
5. Attach the spinner to the propeller driver using the
# 15 7236 central screw.
6. I
NITIATION OF THE
S-BEC"
1. Connect the three wires attached to the speed
controller to the three wires attached to the motor; the
order of connection is unimportant.
2. Locate the UNI connector attached to the speed
controller, and connect it to your receiver.
3. Switch the transmitter on, and check that the throttle
control is at the "OFF" position.
4. Connect the flight battery to the speed controller.
5. Check the direction of rotation of the motor: it should
spin clockwise when viewed from the tail, looking
forward. If this is not the case, disconnect the flight
battery and swap over any two of the three motor wires.
6. Set the motor brake on the speed controller to "brake
ON"; the procedure is described in the speed controller
instructions.
O T P
F HE OWER
S-BEC"
Hexagon driver nut
Blade holder
Propeller driver
P
OWER
S
ET
ensure that the
S "C
ET ULARIS
Page 1/2