Télécharger Imprimer la page

EINHELL TP-AG 18/125 CE Q Li Mode D'emploi page 16

Publicité

Les langues disponibles

Les langues disponibles

6.4 Overload display (Fig. 5/Item 8)
The constant electronics function keeps the
speed constant even when the load increases.
If the load rises too high for the tool, this will be
signaled by fl ashing of the overload display (8).
The following cases will be signaled by the
overload display (8):
Exceeding the maximum power current
permitted for the motor. The overload display
(8) will go off again when the load is reduced
or it will flash for a short time after the tool
has been switched off in order to protect the
motor from the overload.
Exceeding the maximum temperature
permitted for the motor. The overload display
(8) will flash for a short time and will then go
off again. Allow the tool to cool down before
you continue to use it.
6.5 Battery capacity indicator (Fig. 5 / item
11)
Press the battery capacity indicator switch (12).
The battery capacity indicator (11) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs lit:
The battery is fully charged.
2 or 1 LED(s) lit:
The battery has an adequate remaining charge.
1 LED fl ashing:
The battery is empty, recharge the battery.
All LEDs fl ashing:
The temperature of the battery is too low. Remove
the battery from the device and leave it at room
temperature for a day. If the error occurs again,
this means that the battery has been completely
depth-discharged and is defective. Remove the
battery from the device. Never use or charge a
defective battery.
6.6 Changing the grinding wheel (Fig. 6)
The wheel is easy to change using the
spindle lock and quick-clamp nut.
Press the spindle lock and allow the grinding
wheel to engage.
Undo the quick-clamp nut by turning it
counterclockwise by hand (see Fig. 6).
Change the grinding wheel or cutting wheel
and tighten the quick-clamp nut by turning it
clockwise by hand.
Anl_TP_AG_18_125_CE_Q_Li_SPK7_USA.indb 16
Anl_TP_AG_18_125_CE_Q_Li_SPK7_USA.indb 16
EN
Warning!
For safety reasons the quick-clamp nut (5) may
only be used for this angle grinder.
Warning!
The quick-clamp nut must be well tightened to
prevent it from working itself loose during use!
This can be done by turning the grinding wheel
clockwise with a strong tug while keeping the
spindle lock pressed! While you are doing this,
wear gloves to prevent injury.
Notice!
Only ever press the spindle lock when
the motor and grinding spindle are at a
standstill! You must keep the spindle lock
pressed while you change the wheel!
6.7 Grinding wheels
The grinding or cutting wheel must never be
bigger than the stipulated diameter.
Check the specified rotating speed of the
grinding or cutting wheel before use.
The maximum speed of the grinding or
cutting wheel used must be higher than the
idle speed of the angle grinder.
Only use grinding or cutting wheels which are
approved for a minimum rotating speed of
10,500 RPM and for a circumferential speed
of 226 ft/s.
Check the direction of rotation when you use
diamond cutting wheels. The directional arrow
on the diamond cutting wheel must point in
the direction in which the tool rotates.
Take special care that the grinding/sanding
wheels are properly stored and transported.
Ensure that the grinding/sanding wheels are
never exposed to shock, jolts or sharp edges (for
example during transport or storage in a toolbox).
This could cause damage (such as cracks) to the
grinding/sanding wheels and place the user in
serious danger.
6.8 Motor
The motor must be provided with good ventilation
during operation, which means that the air vents
must be kept clean at all times.
- 16 -
01.08.2023 11:25:50
01.08.2023 11:25:50

Publicité

loading

Ce manuel est également adapté pour:

4431148