Flex L 602 VR Notice D'instruction D'origine page 16

 Hold the electric power tool firmly and
position your body and arms to allow you
to absorb kickback forces. If fitted, always
use the auxiliary handle to ensure the best
possible control over the recoil forces or
reaction torques when acceleration
occurs.
The operator can control kickback and
reaction forces by taking appropriate
precautions.
 Keep your hands away from the rotating
insertion tool.
The insertion tool may kickback over your
hand.
 Keep your body out of the area into which
the electric power tool moves when
a recoil occurs.
Kickback propels the electric power tool in the
direction opposite to the movement of the
sanding disc at the point of pinching.
 Work especially carefully near corners,
sharp edges, etc. Prevent the insertion
tool from recoiling off the workpiece and
jamming.
The rotating insertion tool has a tendency to
snag on corners, sharp edges or if it bounces.
This causes a loss of control or kickback.
 Do not use a chain or toothed saw blade.
Such insertion tools frequently cause
a kickback or the loss of control of the electric
power tool.
Special safety instructions
for polishing:
 Do not allow any loose parts of the
polishing hood, in particular fixing cords.
Stow or shorten the fixing cords.
Loose, entrained fixing cords may trap
your fingers or become entangled in the
workpiece.
Additional safety instructions
 The mains voltage and the voltage
specifications on the rating plate must
correspond.
 Do not press the spindle lock until the
tool stops.
16
All manuals and user guides at all-guides.com
Noise and vibration
The noise and vibration values have been
determined in accordance with EN 60745.
The A evaluated noise level of the power tool
is typically:
– Sound pressure level:
– Sound power level:
– Uncertainty:
Total vibration value (when polishing painted
surfaces (with sponge)):
– Emission value:
– Uncertainty:
qÜÉ=áåÇáÅ~íÉÇ=ãÉ~ëìêÉãÉåíë=êÉÑÉê=íç=åÉï=
éçïÉê=íççäëK=a~áäó=ìëÉ=Å~ìëÉë=íÜÉ=åçáëÉ=
~åÇ îáÄê~íáçå=î~äìÉë=íç=ÅÜ~åÖÉK
The vibration emission level given in this
information sheet has been measured in
accordance with a standardised test given
in EN 60745 and may be used to compare
one tool with another. It may be used for
a preliminary assessment of exposure.
The declared vibration emission level
represents the main applications of the tool.
However if the tool is used for different appli-
cations, with different accessories or poorly
maintained, the vibration emission may differ.
This may significantly increase the exposure
level over the total working period. For a precise
estimation of the vibration load the times should
also be considered during which the power
tool is switched off or even running, but not
actually in use. This may significantly increase
the exposure level over the total working period
Identify additional safety measures to protect
the operator from the effects of vibration such
as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.
tÉ~ê=É~ê=éêçíÉÅíáçå=~í=~=ëçìåÇ=éêÉëëìêÉ=
~ÄçîÉ=UR=Ç_E^FK
Polisher L 602VR
`^rqflk>
klqb
`^rqflk>
90 dB(A);
101 dB(A);
K = 3 dB.
2
a = 2.5 m/s
h
2
K = 1.5 m/s