Publicité
Les langues disponibles
Les langues disponibles
Clean the air filter (Fig. 4)
Soiled air filters reduce the engine power by sup-
plying too little air to the carburetor. Dust and pollen
plug up the pores of the filter made of foamed plastic.
Regular checks are therefore essential.
• Unclip (A) the air filter cover (B) and remove the
sponge filter element (C).
• To avoid objects falling into the air tank, replace
the air filter cover.
• Wash the filter element in warm soap water, rinse
and allow drying naturally.
Important: Never clean the air filter with petrol or
inflammable solvents.
In order not to shorten the service life of the engine,
a damaged air filter must be replaced at once.
Warning!
Never run the engine without the air filter ele-
ment installed.
FUEL FILTER
Inside the fuel tank there is a filter which prevents
impurities from entering the engine. The filter should
be replaced once a year by your Retailer.
Our machines have been designed to operate over a
long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon
proper machine care and regular cleaning.
Keep all nuts, bolts and screws tight to be sure the
appliance is in safe working condition.
• Replace worn or damaged parts.
• Use only genuine replacement parts and accesso-
ries
• Store the appliance only in a dry place.
The user is responsible for all damages caused by
non-compliance with instructions in this manual. This
also applies to non-authorized modifications of the
tool, use of non-authorized spare parts, accessories,
working tools, unrelated and not intended use, sec-
ondary damages due to use of faulty components.
Warning!
Use only original manufacturer's replacement parts,
accessories and attachments. Failure to do so can
cause poor performance, possible injury and may
void your warranty.
Important hint in case of sending the equipment
to a service station:
Due to security reasons please see to it that the
equipment is sent back free of oil and gas!
Ordering replacement parts
Please quote the following data when ordering re-
placement parts:
• Type of machine
• Article number of the machine
32 | GB
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the
following parts are therefore also required for use
as consumables.
Wear parts*: Spark plug, Air filter, Fuel filter, Col-
lection bag
* Not necessarily included in the scope of delivery!
10. Storage
Important: Never put the equipment into storage for
longer than 30 days without carrying out the follow-
ing steps.
Storing the equipment
If you intend to store the equipment for longer than 30
days, the equipment must be prepared accordingly.
Otherwise the fuel still remaining in the carburetor
will evaporate and leave a rubbery sediment. This
can cause problems when starting up the equipment
and may require expensive repairs.
• Slowly remove the fuel tank cap to release any
pressure that may have formed in the tank. Care-
fully empty the tank. Empty the tank only outdoors
or in well-ventilated areas. Make sure that no fuel
enters soil (environmental Protection). Use suit-
able base.
• To remove the fuel from the carburetor, start the
engine and let it run until the equipment stops.
• Leave the engine to cool (approx. 5 minutes).
• Remove the spark plug (see section Change and
clean the spark plug).
• Add one teaspoon of 2-stroke engine oil into the
combustion chamber. Slowly pull the starter cord
several times to apply a layer of oil to all internal
components. Fit the spark plug again.
Note: Store the equipment in a dry place and far
away from possible ignition sources such as an oven,
a gas-fired hot water boiler, a gas-fired dryer, etc.
Putting the equipment back into operation
• Remove the spark plug (see section Change and
clean the spark plug).
• Quickly tug on the starter cord to remove excess
oil from the combustion chamber.
• Clean the spark plug and check that the electrode
gap is correct, or insert a new spark plug with the
correct electrode gap.
• Prepare the equipment for operation.
Publicité
