Publicité
Les langues disponibles
Les langues disponibles
Residual risks
Even if used properly, residual risks can exist even if
the relevant safety regulations are complied with due
to the design determined by the intended purpose.
Observing these instructions, and taking proper care,
will reduce the risk of personal injury or damage to
the equipment.
• Injury by catapulted parts.
• Breaking or catapulting of knife pieces.
• Carbon monoxide poisoning when using the device
in closed or poorly ventilated rooms.
• Burning when touching hot parts.
• Impairment of hearing when working on the ma-
chine for longer periods of time without ear pro-
tection.
In addition, in spite of all the precautionary measures
taken, non-obvious residual risks can still exist. Re-
sidual risks can be minimised if the "Safety informa-
tion" and the "Intended usage" as well as the whole
of the operating instructions are observed.
6. Technical data
Dimension L x W x H
Air speed max.
dust bag capacity
Power unit
Displacement
Max. engine output
Idle speed
Fuel tank capicity
Engine type
Blower weight
Vacuum weight
Total weight
Subject to technical changes!
Information concerning noise emission measured ac-
cording to relevant standards:
Sound pressure L
= 97,0 dB(A)
pA
Sound power L
= 108,4 dB(A)
WA
Uncertainty K
= 3 dB(A)
PA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Vibration
Lower handle A
= 15,1 m/s
hv
Upper handle A
= 11,92 m/s
hv
Uncertainty K
= 1.5 m/s
2
PA
1250 x 550 x 370 mm
260 km/h
50 l
25,4 cm
3
0,7 kW
3500 ± 300 min
-1
650 cm
3
2-stroke engine, air-
cooled
4,7 kg
5,9 kg
6,4 kg
2
2
Reduce noise generation and vibration to a minimum!
• Use only equipment that is in perfect condition.
• Maintain and clean the equipment regularly.
• Adopt your way of working to the equipment.
• Do not overload the equipment.
• Have the equipment checked if necessary.
• Switch off the equipment when not in use.
• Wear gloves.
In these operating instructions we have marked
the places that have to do with your safety with
this sign: m
7. Attachment and operation
ATTENTION! Before working on the device - clean-
ing, inspection, maintenance or other work - always
turn off the device.
ATTENTION!
Remove transport protection ring (23) Fig. 1
Assembly blower(Fig. 7-9)
m Warning: The blower must not be used or
switched on until it has been fully assembled.
• Remove the screw (K) and its washers (L).
• Align the first blower tube(4) compartment with the
protrusion of the air outlet, push the tube and turn
it 90° clockwise, in order to permanently fix it in
place.
• Fix the tube (4) to the air outlet using the screw (K)
and its washers (L).
• Align the second blower tube(5) compartment with
the protrusion (P) of the first tube, push the tube
and turn it 90° clockwise, in order to permanently
fix it in place.
m Warning! Use only original manufacturer's re-
placement parts, accessories and attachments. Fail-
ure to do so can cause poor performance, possible
injury and may void your warranty. Never use the
machine without the guard assembled!
Leaf blower
Assembly: (Fig. 6 - 10)
m WARNINGS: The device must not be switched
on or used until it has been fully assembled.
Assembly vacuum collector (Fig. 10 - 14 )
• Warning: The vacuum collector must not be
used or switched on until it has been fully as-
sembled.
• Remove the screw (1) and the washer (2).
GB | 27
Publicité
