BIXOLON SPP-R300 Guide D'installation

KN09-00035A (Rev.1.0)
◈ Information
This installation guide contains quick information required for the product installation.
Refer to the User's Manual in the CD that comes with the product for detailed installation
instructions. The CD contains the following information.
1. Manual: User's, Windows CE Module Program, Code pages, Commands,
Bluetooth & Wireless
2. Driver: Windows driver
3. Utility: VMSM (Virtual Memory Switch Manager),
NV Image Download Manager, Firmware Download Manager
We at BIXOLON maintain ongoing efforts to enhance and upgrade the functions and quality
of all our products. In following, product specifications and/or user manual content may be
changed without prior notice.
◈ Battery Safety Precautions
1. If you observe any abnormal symptom, such as strange smell and overheating, on first use
after purchasing the product, contact your local dealer immediately.
2. Charge the battery only with the exclusive charger specified (optionally provided) by
BIXOLON. The use of an incorrect charger may result in overheating, combustion and/or
explosion of the battery.
3. Do not use or leave the battery in a location exposed to high temperatures or intense direct
sunlight, such as within an automobile. Doing so can cause battery overheating and/or
combustion. In addition, battery performance and product life may be reduced.
4. Do not allow water, seawater or moisture to enter or leak into the battery. If the safety
mechanism within the battery becomes oxidized, the battery may overcharge with
abnormal electrical current and/or voltage so that it may overheat, ignite and/or explode.
5. Do not throw the battery or subject it to strong shock. If the safety mechanism in the
battery is damaged, the battery may be overcharged and, consequently, an adverse
chemical reaction may be generated in the battery.
There is a potential risk of battery overheating, combustion, and/or explosion.
6. Do not use the battery if it is damaged or the exterior is deformed due to external shock or
if it is swollen.
◈ Content Confirmation
SPP-R300 Battery
Power Cord Belt Clip
◈ Product Part Names
Paper Cover
Power Button
Paper Feed Interface Cap
Button
Open
MSR Cover
Button
◈ Installation and Charging
Battery
Installation
※ Note
As the battery is not charged at the time of purchase, charge the battery prior
to product use. (Use the battery charger)
Paper
Installation
All manuals and user guides at all-guides.com
Battery Charger Paper Roll
CD Installation Guide
Hole for mounting
Shoulder Strap
belt strap / belt clip
Connection Holes
Battery
Cable Connection
Power Connection
1. Insert the battery on the rear side of the
printer, aligning the battery hook
properly.
2. Push the battery into the slot until a
snapping sound is heard.
1. Press the open button to open the paper
cover.
2. Insert the paper as shown in the image.
(Remove any remaining core of a fully
used paper roll.)
3. Take care to align the paper correctly.
4. Pull the paper out and close the paper
cover.
5. Tear off any excess paper in the
direction of the side of the printer.
Printer Installation Guide
Mobile Receipt Printer SPP-R300
Battery
Charging
※ Note
The printer may incur serious damage If the battery charger provided by
BIXOLON is not used. BIXOLON is not legally liable for any such damage.
(The voltage and electrical current specifications of the printer and battery
charger must match.)
Belt Strap
Installation
Belt Clip
Installation
◈ Control Panel Usage
POWER BUTTON FEED BUTTON
• POWER BUTTON
This button is used to turn the printer on and off.
• FEED BUTTON
This button is used to feed paper manually, take the self-test and dump hexadecimals.
• ERROR LED
If the red led is lit, the paper cover is open.
If the red led is blinking, either the paper has been fully used or the print head is
overheated.
If the red led continues to blink, it may indicate a more serious problem with the product,
and thus an authorized service dealer should be consulted.
• BATTERY LED
If Three blue led are lit, the battery is fully charged.
If two blue led are lit, the battery is half charged.
If one blue led is lit, the battery is at the lowest charge level.
If the red led is lit, the battery must be charged or replaced.
• STATUS LED (Bluetooth or Wireless LAN)
1) When using Bluetooth
If the printer is ready for wireless communication with any Bluetooth, the green led as
well as the battery status led is turned on..
2) When using wireless LAN
The right indicator shows the signal strength from wireless LAN.
The green led is solid for acceptable signal strength while the green led blinks for weak
signal strength.
※ Note
In power save mode, only the Status led is lit.
◈ MSR Usage
1. Turn off the printer power.
2. Connect the power cord to the battery
charger, and the connect AC power.
3. Open the external interface cap in the
direction of arrow.
4. Connect the battery charger to the
power connector.
1. Insert the belt strap screw into the belt
strap hole.
2. Use a coin to tighten the belt strap
screw as shown in the image.
1. Insert the screw of the belt clip to the
belt clip mounting hole.
2. Fasten the screw of the belt clip with an
object like a coin as shown in the
picture.
(be careful to fasten in the correct
direction.)
ERROR LED BATTERY LED STATUS LED
1. Press the MSR cover to open.
2. Insert the card as shown in the image and
swipe in the direction of the arrow. (can
be done in both directions)
3. When finished using, press the MSR
cover to close it
※ Note
If the card does not register, first check to
see if it is properly aligned. When swiping
the card, the recommended swiping speed is
100 ~ 1200 mm/sec.