BIXOLON SRP-350plusC Mode D'emploi

KN04-00010A(Rev.1.12)
◈ Information
This Installation Guide includes a brief outline of information necessary for product
installation. For more detailed installation information, please refer to the user manual in the
enclosed CD. The contents of the CD include the following.
1. Manual: User Manual, Code Chart, Control Commands
2. Drivers: Windows Drivers, OPOS Drivers
3. Utilities: a Logo download tool and a virtual memory switch control tool
We at BIXOLON maintain ongoing efforts to enhance and upgrade the functions and quality
of all our products. In following, product specifications and/or user manual content may be
changed without prior notice.
◈ Components
SRP-350plusC SRP-350plusA
USB A-A JACK
◈ Connecting the cables
1. Turn off the printer and the host ECR (host computer).
2. Plug the power cord into the Adaptor, and then plug the Adaptor into the power connector
of the printer.
3. Check the interface cable (Serial, Parallel, USB, or Ethernet), and connect the interface
connector cable accordingly.
4. Plug the drawer kick-out cable into the drawer kick-out connector on the printer.
Interface connector
Interface cable
(Serial/Parallel/USB/Ethernet)
◈ Installing the Paper Roll
※ Note: Adjusting the Paper Near-End Sensor
Near end
sensor tab
◈ Using the Operation Panel
• POWER (LED)
When turning on the power, a green LED will be lit.
• ERROR (LED)
When an error occurs, a red LED will be lit.
(e.g. no paper, cover ajar, etc.)
• PAPER (LED)
Red LED will be lit when the paper roll is running low. The LED blinks
when the printer is in self-test standby mode or macro execution standby
mode.
• FEED (Button)
Press the FEED button once to discharge extra paper. Holding down the
FEED button will discharge paper continuously until the button is
released.
THERMAL PRINTER SRP-350/352plusA&C
Cable cover Paper Roll
Procuct Installation CD Procuct Installation CD Procuct Installation CD
CD Installation Guide
AC/DC Adaptor Power cord
Drawer kick-out connector
Power connector
Adaptor
Power cord
Drawer kick-
out cable
1. Open the paper roll cover by pressing the
cover-open button.
2. Insert a new paper roll, making sure to align
it properly.
3. Pull out a small amount of paper, and close
the cover.
※ Note
When closing the cover, press down on the
center of the cover to ensure that the paper is
in contact with the roller.
The SRP-350plus has a paper near-end sensor
that provides notice that the paper roll is
nearly exhausted. When the paper is running
low, the lamp on the apparatus is lit red. If the
lamp is activated even when sufficient paper
remains, adjust the near-end sensor setting by
pushing the tab upward towards 1.
Printer Installation Guide
◈ Setting the DIP Switches
Changing Dip Switch settings must be done when the printer is off. Any changes done while
the printer is on will not be processed.
1. Serial Interface
• DIP Switch 1
SW Function
1-1 Auto Line Feed
1-2 Handshaking
1-3 Data Length
1-4 Parity Check
1-5 Parity Selection
1-6
1-7 Baud Rate Selection (bps)
1-8
• DIP Switch 2
SW Function
2-1 Reserved
2-2 Internal bell control
2-3 Auto Cutter
2-4 Reserved
2-5
2-6 Print Density
2-7
2-8 Near-End Sensor Status
2. Parallel / USB Interface
• DIP Switch 1
SW Function
1-1 Auto Line Feed
1-2 Reserved
1-3 Reserved
1-4 Reserved
1-5 Reserved
1-6 Reserved
1-7 Reserved
1-8 Reserved
• DIP Switch 2
SW Function
2-1 Reserved
2-2 Internal bell control
2-3 Auto Cutter
2-4 Reserved
2-5
2-6 Print Density
2-7
2-8 Near-End Sensor Status
※ Note
You can adjust external buzzer control via VMSM utility.
• Table 1 – Baud rate (bps) Selection
Transmission Speed
2400
4800
9600
19200
38400
57600
115200
• Table 2 – Print Density Selection
2-5 2-6
ON ON
OFF OFF
ON OFF
OFF ON
2-5 2-6
ON ON
ON ON
OFF OFF
OFF OFF
ON OFF
ON OFF
OFF ON
OFF ON
ON OFF
Enable Disable
XON/XOFF DTR/DSR
7bits 8bits
Yes No
EVEN ODD
Refer to the following table 1
ON OFF
- -
Internal bell disable Internal bell enable
Disable Enable
- -
Refer to the following table 2
Disable Enable
ON OFF
Enable Disable
- -
- -
- -
- -
- -
- -
- -
ON OFF
- -
Internal bell disable Internal bell enable
Disable Enable
- -
Refer to the following Table 2
Disable Enable
1-6 1-7 1-8
ON OFF OFF
ON OFF ON
OFF ON OFF
OFF OFF OFF
OFF ON ON
OFF OFF ON
ON ON ON
2-7 Print Density (Mono color)
Reserved 1(Light)
Reserved 2
Reserved 3
Reserved 4(Dark)
2-7 Print Density (Two colors )
ON 80%
OFF 90%
ON 95%
OFF 100%
ON 105%
OFF 110%
ON 120%
OFF 130%
Default
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
Default
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Default
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
Default
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Default
9600
Default
2
Default
100%