CDVI KCIEN Manuel D'installation page 8

INSTALLATION MANUAL
KCIEN - KCIENSBP
Illuminated Weatherproof Keypad - Self Contained
Description:
12V to 24V ac power supply
or 12V to 48V dc.
Illuminated 12 key keypad.
Non-volatil EPROM memory.
100 programmable codes
in 4, 5 or 6 digits.
2 form "C" contact N/O & N/C
6A/250V~.
Master code programmable
in 4, 5 or 6 digits.
Warning buzzer.
1 request - to - exit input.
Factory master code and code reset.
Code change by the user
Default values:
No codes.
Illumination time: 10 seconds.
Relay release time: 1 second.
Code length: 5-digits.
Master Code: 1 2 3 4 5.
Programming security-lag: 120s.
A. Resetting the memory
1. Enter the master code twice.
- For the first use, the factory
master code is: 1 2 3 4 5.
- Two beeps are emitted to confirm
entry in programming mode.
2. Then press A6.
- A short beep sounds is emitted.
- Press A and B to confirm the resetting.
- Wait for a beep to be emitted
and for the lighting to go off.
- The master code is 1 2 3 4 5 again
and all the codes have been erased.
- The keypad is reinitialised.
- The keypad is no longer
in the programming mode and the default
values have been restored.
OR
1. Turn off the power supply.
Place a jumper at ST3 (See P. 6).
2. Turn the power supply on again.
Wait a few seconds, a beep is emitted.
3. The master code is 12345 again
and all the codes have been erased.
The default values have been restored.
Code length for sub master code:
- Version 1 relay (Group 1) = A and B,
- Version 2 relays (Group 2) = 1 and 3.
One beep on switching on.
Audible signal correspondence:
- 1 short beep: Keypad powered
- 1 long beep: data computing
in programming or access granted.
- 2 beeps: Enter or Exit
from programming.
- 4 short beeps: data computing error.
Digits used and opening codes:
- The master code and the User codes
can be of 4 or 5-digit in length.
All the keypad keys can be used
to program a code. The master code
and the Pin code can be of 4, 5
or 6-digit code. The master code
can not be used as a PIN code
(User Pin code).
- Codes 0 0 0 0 0 0, 0 0 0 0 0
and 0 0 0 0 can only be used
B. Setting code length
1. Enter the master code twice.
2. Press A4 to input the number of digits
3. Press A5 to change the master code.
4. Press B to exit from
4 beeps indicate a data computing error.
to delete a user Pin code.
Control by push button:
- The connection of push button P1
is intended for controlling relay 1.
(the mode and the time-lag
can be programmed).
- Clock contact H1 enables use
of the outside button for free
opening. Clock contact H2 enables
use of all the keys as outside buttons.
If the clock contact is open, the keys
are used like normal digits.
If the clock contact is closed,
all the keys can be used for free access.
Consumption
(without the control elements)
With the 2 relays controlled
and permanent lighting:
- In 12V dc > 90mA max,
- In 12V ac > 70mA max,
- In 24V dc > 50mA max,
- In 24V ac > 40mA max.
- For the first use, the factory
master code is: 1 2 3 4 5.
- Two beeps are emitted to confirm
entry in programming mode.
in the codes.
- A short beep sounds is emitted.
- Enter 4, 5 or 6 for number of digits.
- A long beep sounds is emitted to confirm
the programming.
- A short beep sounds is emitted.
- Enter the 4, 5 or 6 digits of the new
master code.
- A long beep sounds is emitted to confirm
programming of the newmaster code.
the programming mode.
Two beeps sound are emitted to confirm
the return to the normal mode of operation.
EN
7
cdvigroup.com