Bort ALLIGATOR Mode D'emploi page 13

supply from the outlet and check the air duct pneu-
matic switch and delivered to the outlet electricity .
• This product is designed for grinding food residues
at home; the ingress of substances other than food
into the disposer may cause injury and / or damage
property . To reduce the risk of Do not use a washer
with an installed disposer not for food purposes (for
example, for bathing a child or washing your head) .
• Children should be supervised adults and should not
play with a disposer . To reduce the risk of injury It is
necessary to keep a watchful eye on children use of
the product .
• If the wedging in the disposer is eliminated, turn off
the appliance and disconnect it from the electrical
network . Use a wrench for self–removal of jammed
waste according to description in the section "Elimi-
nation of jamming disposer ".
• Use tongs or pliers to remove foreign objects from the
product .
• To reduce the risk of injury from particles that
are thrown out by the disposer, it is prohibited to
use grinders withoutnoise shielding screen (Fig .
8 .3) . Place the plug in the drain hole, as shown in
Fig . 11 .2 or 11 .4 .
• Do not allow the following items to fall into the dis-
poser: shells, including oyster, caustic means for
cleaning pipes or similar chemical products, glass,
porcelain or plastic, large (hollow) bones, metal ob-
jects (bottle caps, cans, or kitchen appliances), hot fat
or other hot liquids .
• Replace worn noise glossy screen / installation gas-
ket / protective reflector if they are worn and are no
longer able to prevent waste or water .
• If the disposer is switched off, use a stopper to pre-
vent foreign objects in the grinding camera . Make
sure that the power of the disposer is disabled .
• Before pressing the reset button, cleaning the jam or
removing foreign objects from the shredding cham-
ber, make sure that the food is turned off .
• Keep hands and fingers out of the reach of disposer
chamber .
FIRE RISK:
To minimize the possibility of Do not store near fire ex-
tinguishing articles such as rags, paper or aerosol cans .
Do not store or use gasoline or other flammable va-
por–gas mixtures and liquid near the disposer . Do not
allow the following camera products: paints, solvents,
household cleaning agents and chemicals, automotive
liquids, plastic packaging .
USER'S MANUAL
1 . Use air switch (Fig . 11 .1) for starting disposer .
2 . Slowly lower food waste into the chamber and in-
stall the filter grid in a vertical position (so that it flows
through it water) to reduce noise and possible throwing
waste during grinding (Fig . 11 .2) .
3 . After the grinding is completed, turn off the disposer
and let the water run for at least 15 s to flush the drain
line .
SHOULD
Grind food waste under pressure cold water not less
than 6 liters / min .
Grind solids, such as small bones and fruit residues, for
cleaning chopping chambers .
Grind citrus fruits, melons, vegetables and coffee
beans .
After the grinding is finished, let the water run out at
least 15 seconds to flush the drain pipeline.
Unplug the product from the socket before removing
the seized rotor with a tool .
Do not store any objects under the display to ensure
access to the button restart .
DO NOT
Do not use hot water when grinding remains of prod-
ucts (although hot water through the product between
grinding) .
Do not turn off the water or the product until the grind-
ing is completed, there is a noise of running engine and
running water .
Do not grind large amounts of egg shells, fibrous mate-
rials, for example corn husks, artichokes, etc ., in order
to avoid possible clogging of the pipe .
Grind only food .
• Do not use this appliance to grind hard materials,
such as glass and metal .
• Never pour fat, oil or fat in shell, as this will lead to
clogging drainage and sewerage systems .
• Do not fill the disposer chamber with a large amount
of cleaning vegetables. Instead, turn on the water first
and disposer and gradually lower it cleaning .
CLEANING THE DISPOSER CHAMBER
Over time, fat / food particles can accumulate in the
grinding chamber and protective reflector, causing an
unpleasant smell .
For cleaning grinding chamber and reflector:
1 . Turn off the EQUIPMENT and disconnect it from the
mains .
2 . Through the drain hole using a sponge for washing,
clean the bottom surfaces protective reflector and inner
13