Publicité
Les langues disponibles
Les langues disponibles
Installation
! Before placing your new appliance into operation please read these
operating instructions carefully. They contain important information for
safe use, for installation and for care of the appliance.
! Please keep these operating instructions for future reference. Pass
them on to possible new owners of the appliance.
Positioning and connection
Positioning
1. Place the appliance in a well-ventilated humidity-free room.
2. Do not obstruct the rear fan grills. The compressor and condenser
give off heat and require good ventilation to operate correctly and
save energy.
3. Leave a space of at least 10 cm between the top part of the
appliance and any furniture above it, and at least 5 cm between
the sides and any furniture/side walls.
4. Ensure the appliance is away from any sources of heat (direct
sunlight, electric stove, etc.).
5. In order to maintain the correct distance between the appliance
and the wall behind it, fit the spacers supplied in the installation kit,
following the instructions provided.
Levelling
1. Install the appliance on a level and rigid floor.
2. If the floor is not perfectly horizontal, adjust the refrigerator by
tightening or loosening the front feet.
Electrical connections
After the appliance has been transported, carefully place it vertically
and wait at least 3 hours before connecting it to the electricity mains.
Before inserting the plug into the electrical socket ensure the following:
• The appliance is earthed and the plug is compliant with the law.
• The socket can withstand the maximum power of the appliance,
which is indicated on the data plate located on the bottom left side
of the fridge (e.g. 150 W).
• The voltage must be in the range between the values indicated on
the data plate located on the bottom left side (e.g. 220-240V).
• The socket is compatible with the plug of the appliance. If the
socket is incompatible with the plug, ask an authorised technician
to replace it (see Assistance). Do not use extension cords or
multiple sockets.
! Once the appliance has been installed, the power supply cable and
the electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by authorised
technicians only (see Assistance).
! The manufacturer declines any liability should these
The manufacturer declines any liability should these
The manufacturer declines any liability should these
The manufacturer declines any liability should these
The manufacturer declines any liability should these
safety measures not be observed.
safety measures not be observed.
safety measures not be observed.
safety measures not be observed.
safety measures not be observed.
Start-up and use
Starting the appliance
! Before starting the appliance, follow the installation instructions
(see Installation).
! Before connecting the appliance, clean the compartments and
accessories well with lukewarm water and bicarbonate.
! The appliance comes with a motor protection control system which
makes the compressor start approximately 8 minutes after being
switched on. The compressor also starts each time the power supply
is cut off whether voluntarily or involuntarily (blackout).
1. Insert the plug into the socket and ensure that the internal light
illuminates ( the FREEZER OPERATION knob must not be on the
position OFF) .
2. Turn the FREEZER OPERATION knob and REFRIGERATOR
OPERATION knob to an average value. After a few hours you will
be able to put food in the refrigerator.
Setting the temperature
The temperature inside the refrigerator compartment automatically
adjusts itself according to the position of the thermostat knob.
min = warmest
max = coldest
We recommend, however, a medium position.
The No Frost system circulates cold air continuously to collect humidity
and prevent ice and frost formation. The system maintains an optimal
humidity level in the compartment, preserving the original quality of
the food, preventing the food from sticking together and making
defrosting a thing of the past. Do not block the aeration cells by
placing food or containers in direct contact with the refrigerating back
panel. Close bottles and wrap food tightly.
*
FRUIT and VEGETABLE bin
The salad crispers fitted inside the fridge have been specially
designed for the purpose of keeping fruit and vegetables fresh and
crisp. Open the humidity regulator (position B) if you want to store
food in a less humid environment like vegetable, or close it (position
A) to store food in a more humid environment like fruit.
A
B
*
ICE DEVICE
After pouring water in the special ice cups, place them in their places
in the ice device. After about 2 hours, the ice cubes will be ready. In
order to get the ice cubes, it will be sufficient to turn the two buttons to
the right. The ice cubes will fall in to the tray below, ready to be used.
*
: : : : : A compartment designed to keep meat
Food Care Zone 0°C
and fish freshness.Due to the compartment's low temperature (-2/
+3) food can be stored for even up to one week. It can also be used
for "cold meals." Not suitable for fruit, vegetables and salads.
GB
7
Publicité
