Publicité
Les langues disponibles
Les langues disponibles
2. The extension cord must have a ground wire and plug pin
and be connected to a properly functioning GFCI
receptacle.
3. Make sure the connection between the transformer and
extension cord are elevated off the floor.
SECURITY SYSTEM INSTALLATION AND SETUP
Electric shock hazard. Disconnect
power before servicing. Apply a fixed
lock or tag to prevent unexpected application of power.
The advanced notification system produces auto-dialer alerts
and can also notify your 3rd party home security system
provider (if available). A qualified home security technician is
required when making connections between the two systems.
An access port is available on the back of the lid in which
the qualified technician can properly connect the advanced
notification system to the security system. (See Figure 5)
Figure 5 - Security system setup
The inner shield will have to be removed during
this step. Be sure not to damage any
components on the control board.
At this time, you may wish to change the system settings.
Since both the auto-dialer and security system cannot access
the phone line at the same time, you must choose which
system the software accesses first. If you wish the security
system to have first priority, on the main menu, scroll to and
select the "SECURITY SETUP" option, select "Security has
Priority" and hit "Enter" to confirm. The factory default setting
is "Back-up has Priority".
If you choose, you can test the security notification by
simulating any of the security notification alerts. (See Figure 6)
DO NOT overtighten screw.
Replace the inner shield once all connections and tests have
been validated.
OPERATING INSTRUCTIONS
1. To test the back-up pump, unplug the main pump and
transformer and fill sump with water until the water lifts the
bottom float therefore activating the back-up pump. Repeat
this process two times to be sure pump is operating
normally.
2. If pump operates normally, plug the transformer into wall
outlet and plug the main pump back in. Verify the main
pump is operational by repeating step 1 above.
FCC STATEMENT
This equipment complies with Part 68 of the FCC rules and
the requirements adopted by the ACTA (American Council
for Terminal Attachments). On the inside cover of your unit
is a label that contains, among other information, the FCC
registration number for this product. If requested, this number
Model RSM3300 – Operating Instructions and Parts Manual
FOR SIGNAL
USAGE ONLY. NC/NO Output:
12 Volt DC, 2 amp max.
Ridge Tool Company
must be provided to the telephone company.
PLUG AND JACK USE
A plug and jack used to connect this equipment to the premises
wiring and telephone network must comply with the applicable
FCC Part 68 rules and requirements adopted by the ACTA.
A compliant modular plug is provided with this product. It is
designed to be connected to a compatible modular jack that is
also compliant. See installation instructions for details.
RING EQUIVALENCE NUMBER (REN)
The REN is used to determine the number of devices that may be
connected to a telephone line. Excessive REN's on a telephone line
may result in the devices not ringing in response to an incoming
call. In most, but not all areas, the sum of RENs should not exceed
five (5.0). To be certain of the number of devices that may be
connected to a line, as determined by the total REN's, contact your
local telephone company. The REN for this product is listed on the
inside of the controller lid with the FCC identifier.
TELEPHONE NETWORK INTERFERENCES
If this System causes harm to the telephone network, the
telephone company will notify you in advance that temporary
discontinuance of service may be required. But if advance notice
isn't practical, the telephone company will notify the customer
as soon as possible. Also, you will be advised of your right to
file a complaint with the FCC if you believe it is necessary. The
telephone company may make changes in its facilities, equipment,
operations or procedures that could affect the operation of the
equipment. If this happens, the telephone company will provide
advance notice in order for you to make necessary modifications
to maintain uninterrupted service. If the equipment is causing harm
to the telephone network, the telephone company may request
that you disconnect the equipment until the problem is resolved.
If your home has specially wired alarm equipment connected to
the telephone line ensure the installation of your System does not
disable your alarm equipment. If you have questions about what
will disable alarm equipment, consult your telephone company or a
qualified installer.
ADVANCED NOTIFICATION
CONDITION
PRIMARY PUMP STATUS
AC Power Interrupted
Primary Pump Suspect
BACK-UP DC PUMP STATUS
DC Pump In Operation
DC Pump Not Operable (Failed Test)
Check Floats For Debris
Capacity Overflow Possible
DC Impeller Locked
BATTERY TRANSFORMER
Transformer Bad
MICROPROCESSOR CONTROLLER
Blown Controller Fuse
12 V BATTERY STATUS
DC Pump Under Test
Battery Fully Charged
Battery 80% Charged
Battery 60% Charged
Battery 40% Charged
Battery 20% Charged
Battery Dead
Battery Condition Questionable
Reverse Polarity
MESSAGE ON UNIT SCREEN
AUDIBLE ALARM
Figure 6 -Notification alerts chart
SECURITY SYSTEM
CALL PHONE
9
Publicité
