Cleaner Maintenance; Using Your Cleaner - Hoover 48024008 Manuel D'utilisation

GETTING TO KNOW YOUR CLEANER
A. Main Cleaner
B. Bin Lid Latch Left/Right
C. Hose
D. Water Tank
E. Bin Handle
F. Bin Release Button
G. Carry Handle
H. Cord Reel Pedal
I. Variable Power Control Knob
J. On/Off Pedal
K. Hose Handle
L. suction Regulator
M. Telescopic Tube
N. Telescopic Tube Adjuster
O. Tool holder
P. Carpet And Floor Nozzle (GP)**
P1. Hard Floor Nozzle (HF)**
P2. Carpet Nozzle (CA)**
ASSEMBLING YOUR CLEANER
Remove all components from the packaging.
1. Press the bin release button and remove the bin assembly from the cleaner, by holding
the bin handle. [1]
2. Open the bin lid latch left/right and remove the bin lid from the bin assembly. [2]
3. Fill the water tank with ordinary tap water between MIN and MAX. Do not overfill above
the MAX level. [3]
4. Re-assemble the bin lid onto the water tank, locking both left and right latches. [2]
5. Refit the bin assembly onto the product ensuring it is firmly locked. [1]
6. Connect the hose to the cleaner main body, ensure it clips and locks. [4] To release the
hose: simply press the two latches on the hose end and pull. [4]
7. Connect the hose handle to the tube upper end, ensure it clips and locks. [5A]
8. Connect the tube lower end to carpet and floor nozzle**. [6A]
9. Clip the tool holder on the tube so that the tools* [X1, X2, X3] can be stored. [7] The
tools* can be fitted to the handle and/or tube when used. [5B, 6B]

USING YOUR CLEANER

ENSURE THE WATER TANK IS FILLED WITH WATER BETWEEN MIN AND MAX
BEFORE USING CLEANER. IF THE WATER TANK IS EMPTY, PLEASE REFER TO
"ASSEMBLING YOUR CLEANER " FROM STEP 1 TO STEP 5.
Q. Dust Container Latch
R. Emptying Latch
s1. Pre-motor Filter Foam A
s2. Pre-motor Filter Foam B
s3. Pre-motor Filter Foam C
T. Pre-motor EPA Filter
U. Parking slot
V. Exhaust Filter Cover
W1. Exhaust Filter A
W2. Exhaust Filter B
W3. Exhaust Filter C
X1. Crevice Tool*
X2. Dusting Brush*
X3. Furniture Nozzle*
Y. Pet Hair Remover Mini Turbo Nozzle*
Z. Allergen Remover Mini Turbo Nozzle*
AA. Parquet Nozzle*
1. Extract the power cord and plug it into the power supply. Do not pull the cord beyond
the red mark. [10]
2. Adjust the telescopic tube* to the desired height by moving the telescopic tube adjuster*
to the most comfortable cleaning position. [8]
3. Carpet & Floor Nozzle**. Press the floor type selector on the nozzle [9] to select the
ideal cleaning mode for the floor type.
Hard Floor – Brushes are lowered to protect the floor.
Carpet – Brushes are raised for deeper cleaning.
4. switch the cleaner on by pressing the On/Off Pedal on the cleaner main body. [11]
5. Adjust the variable power control knob to increase or decrease the power. [11]
6. Adjust the suction regulator to the desired level.
7. switch off at the end of use by pressing the on/off Pedal. Unplug and press the cord
reel pedal to wind the power cord back into the cleaner. [12]
NOTE: After every use, ensure the water tank is emptied and cleaned. This product
is for dry vacuum only and MUST NOT be used for wet pick up or on wet surfaces.
PARKING AND STORAGE SECTION
The tube can be parked on the back of the cleaner for storage or temporary storage while
in use. [13]

CLEANER MAINTENANCE

EMPTYING AND CLEANING THE WATER TANK, BIN CYCLONE AND DUST CONTAINER
1. Turn the cleaner off by pressing the On/Off pedal [11] and unplug the power cable. [12]
2. Press the bin release button and remove the bin assembly from the cleaner, by
holding the bin handle. [1]
3. Open the bin lid latches left and right and remove the water tank from the bin
assembly. [2]
4. Empty the dirty water from water tank and clean the water tank. [14]
5. Pull the empty latch and empty the dust container. [15]
6. Close the dust container bin flap.
7. Open the dust container latches and remove the bin lid [16], remove the cyclonic unit
and clean it. [17]
8. Refit the cyclonic unit to the bin lid, refit to the bin assembly and lock the dust container
latches. [16]
9. Refit the bin lid assembly to the water tank and lock the bin lid latches left and right. [2]
10. Refit the bin assembly to the cleaner and ensure it clips and locks. [1]
Cleaning the Filter
To maintain optimum performance of your cleaner, wash the pre-motor EPA filter, foam
filters and exhaust filters after every use.
Cleaning the pre-motor filters:
1. Press the bin release button and remove the bin assembly from the cleaner, by
2
*Certain Models Only
GB
**May vary according to the model