Publicité
•
Undo and remove the two bolts holding the heel guard and master cylinder as arrowed in
picture 8 (please note these bolts have nuts on the inboard side, please use these to loosen the
bolts).
•
Remove the return spring and bracket arrowed in picture 9.
•
Unclip and remove the master cylinder shaft retaining clip as arrowed in picture 10.
•
Loosen the lock nut and remove the master cylinder shaft fork end as shown in picture 11 and
Page | 7
replace with the new ball joint from kit as shown in picture 12.
•
Undo and remove the two bolts arrowed in picture 13 and carefully remove the original foot
rest bracket.
•
Using the bolt and spacer from the kit connect the ball joint as shown in picture 14.
•
Using the two M6 bolts from kit (item 9) and the original nuts attach the master cylinder to the
master cylinder bracket as shown in pictures 15 and 16 (please ensure the master cylinder
pressure shaft is directly in line with master cylinder).
•
PLEASE NOTE FAILURE TO DO THIS MAY RESULT IN BRAKE FAILURE
AND/OR JAMMING OF BRAKES.
•
Offer the right hand side assembly (item 8) into position and secure using the two shorter
remaining M8 bolts from kit (item 10) as shown in picture 17.
•
Using the remaining M8 bolt secure the exhaust as shown in picture 18.
•
Adjust the foot rest and toe peg for comfort and operation (please be aware not all positions
are usable as there is an impact cushion secured to the inboard face of the rear-set (it may be
moved it achieve the required result).
•
Before riding please check all bolts are tightened and the operation and position of all parts.
•
Please check operation of the brake before riding.
•
Tighten all bolts and lock-nuts.
•
Please check operation of the brake before riding.
Because of the complexity and inherent dangers involved in undertaking any work
involving the braking system we strongly recommend a qualified mechanic fits/or checks
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other
than those in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality
and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable
skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for
ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products
R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have
been modified or used or maintained otherwise than in accordance with R&G's or manufacturer's instructions and good
engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting
its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability
shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect
the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they
were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be
in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the
gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No
returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not
refer to faulty goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
after the fitting of this product.
ISSUE 2
05/07/2021 (DM)
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
R&G Racing
www.rg-racing.com
RSET026
Email:
info@rg-racing.com
Publicité
