Télécharger Imprimer la page

Haier HW80-BD1626 Mode D'emploi page 11

Masquer les pouces Voir aussi pour HW80-BD1626:

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 31
Troubleshooting
Display code
Code
Cause
Auto
Automatic
load detection.
Lo
Weighing the laundry load in
/HALF
the drum.
/FULL
/HI
1:25
Remaining wash cycle time.
19:30
Remaining wash cycle time.
Lock
Door cannot be opened due to
water level or hot water in the
drum.
End
End of cycle.
E1
Drainage error, water not emptied. Clean pump filter.
E2
Lock - error.
E4
Water level not reached after 8
minutes.
E8
Water protective level - error.
F3
Temperature sensor - error.
F4
Heating error (Appears at the end of
a cycle . )
F7
Motor - error.
Fb
Water overflow.
FA
Water level sensor error.
FC
Electronic control - error.
Unb
Unbalanced load and not able to
spin.
Warning!
Code Fb: Water-overflow protection is placed on deepest part of appliance. In case of leacka-
ge all functions will be shut down automatically except drain pump which will be activated for
safety reasons.
All manuals and user guides at all-guides.com
Solution
Laundry weight detection in progress, please
wait until program cycle time is displayed.
Please wait until program cycle time is
displayed: Lo = small load;HALF = half load;
FULL = optimized weight load;
HI = full load.
Refer to additional symbol.
End is likely delayed - refer to symbol.
Wait to the end of program or cancel the
program and select the drain program. In
case of hot water is in the drum, to avoid
scalding, select a handwash program and
wash several minutes and then select a
draining program before open the door.
Check drain hose for blockage and proper
installation.
Shut the door properly.
Check if water supply and water pressure
is normal.
Drain hose is self-syphoning.
Auto release.Otherwise contact the
After sales service.
Contact the After sales service.
Contact theAfter sales service.
Contact theAfter sales service.
Close tap immediately.
Contact theAfter sales service.
Contact theAfter sales service.
Contact theAfter sales service.
Check and balance the laundry load in the
drum. Also reduce the load if too heavy.
Restart with a spin program.
20
21
In case of power failure
The current programme and its setting will be saved only
f
r o
a
h s
r o
t t
m i
. e
needed.
If a power failure cuts an operating wash programme door
opening is mechanically blocked.To get out any laundry
water level should not be seen in the glassy porthole of the
door - danger of burns!
W
t a
r e
e l
e v
h l
s a
o t
Not till then pull lever beneath service flap until door is
unlocked by a gentle click.Afterwards refix all parts.
Troubleshooting without display code
Problem
Washing machine
fails to operate.
Washing machine
will not be filled
with water.
Machine is draining
while being filled
r P
b o
b a
y l
a
e n
w
r p
g o
a r
m
m
e
c
c y
e l
s
a t
t r
e b
o l
w
r e
d e
s a
d
s e
r c
b i
d e
n i
"
u P
m
p
e t l
Cause Solution
Programme is not yet started.
Door is not properly closed.
Machine has not been switched on. Switch the machine on.
Power failure.
No chosen programme.
No water.
Inlet hose is kniked.
Inlet hose filter is blocked.
Water pressure is less than
0,03 MPa.
Water supply failure.
Height of drain hose is
below 80 cm.
Drain hose end could
reach into water.
Troubleshooting
lever
s i
. " r
Press "Start/Pause" button.
Close the door properly.
Check power supply.
Set programme and start it.
Check water tap.
Check inlet hose.
Unblock inlet hose filter.
Check water pressure.
Ensure the water supply.
Make sure that drain hose
is properly installed.

Publicité

loading