Publicité
i959191.book : i95919us.fm Seite 1 Montag, Januar 14, 2002 12:49 PM
Technical Data
Minimum flow pressure
Max. operating pressure
Recommended flow pressure
Test pressure
Flow rate
Per shower
max. flow rate 9.5 l/min or 2.5 gpm/ 80 psi
Installation
Note
• In the case of shower doors which open inwards, install
on the appropriate wall side.
• When installing e.g. on plasterboard walls (not solid
walls) it must be assured that an appropriate
reinforcement is in place to ensure sufficient strength.
• Installation height (X) see Fig. [1] and [6] should be
adapted to the body height of the user.
Recommended installation height:
Body height approx.
63" 65" 67" 69" 71" 73" 75"
Installation height (X)
61" 63" 65" 67" 69" 71" 73"
approx.
Surface mounting Freehander 27 006
5
1.Mark position of fixing holes for ø
plugs with the aid of the supplied rubber sheet (K) and then
drill, see fold-out page III Fig. [1].
When installing directly above the shower fitting, it must be
ensured that the Freehander is higher than the fitting when
folded down, see Fig. [2].
2.Install Freehander, see Fig. [3]. The cap (A) must be
removed prior to installation and re-attached subsequently.
3.Install the attached snap coupling (B) on the supplied
shower spray hose of the shower fitting and attach to the
Freehander connection (C), see Fig. [4].
4.If an additional existing or new hand spray is used, the
supplied outlet nipple (D) must be installed onto the hand
spray, see Fig. [5]. Wall shower holder order no. 28 605 can
be ordered as an additional holder for the hand spray.
Concealed mounting Freehander 27 007
1.Prepare 1/2" NPT-MIP shower connection, see Fig. [6].
5
2.Mark position of fixing holes for ø
plugs with the aid of the supplied drilling template and then
drill, see fold-out page V Fig. [7].
For subsequent installation, as a replacement for an
existing overhead spray with a connection height of
3
approx. 80
/
" (2050mm), the user height can be reached
4
using installation set order no. 27 009 see Fig. [8].
3.Remove cap (E) and union nipple (F), see Fig. [9].
4.Install Freehander, see Fig. [10].
Please pass these instructions on to the user of the fitting.
1
The right to make technical modifications is reserved.
All manuals and user guides at all-guides.com
English
Operation of shower heads, see Fig. [11].
14.5 psi
Three functions can be set by turning the adjustment ring (G).
72.5 psi
• Front shower (H)
29.0 - 43.5 psi
87 psi
• Rear shower (I)
Important:
• The bracket of the Freehander is not a safety handle and
must not be used as a handle when leaving the bath.
• Exercise caution when touching the Freehander
following thermal disinfection as the water-bearing pipe
reaches a very high temperature.
Use of the Freehander
1.Overhead spray, see Fig. [12].
2.Side spray, see Fig. [13].
Maintenance
Inspect and clean all parts, replace if necessary and grease
/
" (ø 8mm) mounting
with special fitting grease (order no. 18 012) if required.
16
Turn off hot and cold water supply
I. Shower head
Disassembly, see Fig. [14].
The function of the SpeedClean nozzles is guaranteed for a
period of five years.
Simply rub SpeedClean nozzles in order to remove lime scale
from spray jet, see Fig. [15].
/
" (ø 8mm) mounting
16
Replacement parts, see fold-out page III ( * = special
accessories).
Care
For directions on the care of this fitting, please refer to the
accompanying Care Instructions.
Position: MASSAGE
Position: NORMAL
Position: ECO
Position: MASSAGE
Position: NORMAL
Position: STOP= shut off
shower
Publicité
