Télécharger Imprimer la page

Makita LS1216 Manuel D'instructions page 28

Masquer les pouces Voir aussi pour LS1216:

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 31
2.
Bevel angle
Push the latch lever forward fully to release the positive
stops.
1)
0° bevel angle
Push the carriage toward the guide fence and
tighten the locking screw clockwise and pull the lock
lever towards the front of the saw to secure the car-
riage. Lower the handle fully and lock it in the low-
ered position by pushing in the stopper pin. Loosen
the lever at the rear of the tool. (Fig. 69)
Turn the hex socket bolt on the right side of the arm
holder two or three revolutions counterclockwise to
tilt the blade to the right. (Fig. 70)
Carefully square the side of the blade with the top
surface of the turn base using the triangular rule, try-
square, etc. by turning the hex socket bolt on the
right side of the arm holder clockwise. Then tighten
the lever securely. (Fig. 71)
Make sure that the pointers on the arm holder point
to 0° on the bevel scale on the arm. If they do not
point to 0°, loosen the screws which secure the
pointers and adjust them so that they will point to 0°.
(Fig. 72)
2)
45° bevel angle (Fig. 73)
Adjust the 45° bevel angle only after performing 0°
bevel angle adjustment. To adjust left 45° bevel
angle, loosen the lever and tilt the blade to the left
fully. Make sure that the pointer on the arm holder
points to 45° on the bevel scale on the arm. If the
pointer does not point to 45°, turn the left 45° bevel
angle adjusting bolt on the side of the arm until the
pointer points to 45°.
To adjust right 45° bevel angle, perform the same
procedure described above.
Adjustment of the laser line position (Fig. 74 & 75)
For models LS1216L and LS1216FL only
WARNING:
• Since the tool must be plugged in while adjusting
the laser line, special care must be taken to not
switch on the tool. Accidental start up of the tool may
result in serious personal injury.
CAUTION:
• Never look directly into the laser beam. Direct eye
exposure to the beam could cause serious damage to
the eyes.
• LASER RADIATION
Do not stare into beam.
NOTICE:
• Beware that impacts to the tool may cause the laser
line to be misaligned or may cause damage to the
laser, shortening its life.
28
All manuals and user guides at all-guides.com
Adjusting the laser line for the left side of the blade.
1
2
3
4
5
009514
Adjusting the laser line for the right side of the
blade.
1
2
3
009515
For both adjustments, do as follows.
1.
2.
3.
4.
5.
6.
The position of laser line can be changed as the movable
range of the adjusting screw for the laser is changed by
turning two screws with a hex wrench. (The movable
range of laser line is factory adjusted within 1 mm from
the side surface of blade.)
To shift the laser line movable range further away from
the side surface of blade, turn the two screws counter-
clockwise after loosening the adjusting screw. Turn these
two screws clockwise to shift it closer to the side surface
of the blade after loosening the adjusting screw.
Refer to the section titled "Laser beam action" and adjust
the adjusting screw so that the cutting line on your work-
piece is aligned with the laser line.
1
2
Screw to change the movable range of the adjusting
screw
Adjusting screw
Hex wrench
Laser line
Saw blade
1
Adjusting screw
Saw blade
Laser line
Make sure that the tool is unplugged.
Draw the cutting line on the workpiece and place it
on the turn table. At this time, do not secure the
workpiece with a vise or similar securing device.
Lower the blade by lowering the handle and just
check to see where the cutting line and the position
of the saw blade is. (Decide which position to cut on
the line of cut.)
After deciding the correct position of the line in rela-
tion to the blade, return the handle to the original
position. Secure the workpiece with the vertical vise
without shifting the workpiece from the pre-checked
position.
Plug the tool and turn on the laser switch.
Adjust the position of laser line as follows.
4
5
3
2
3

Publicité

loading

Ce manuel est également adapté pour:

Ls1216lLs1216fLs1216fl