Milwaukee T-TEC 201 Instructions D'utilisation page 18

TECHNICAL DATA
Nominal power output ...................................................................
Rated output ..................................................................................
No-load speed, 1st gear/2nd gear .................................................
Speed under load max., 1st gear/2nd gear ...................................
Percussion rate .............................................................................
Rate of percussion under load max. ..............................................
Static jamming moment*, 1st gear/2nd gear .................................
Drilling capacity in concrete ...........................................................
Drilling capacity in brick and tile ....................................................
Drilling capacity in steel .................................................................
Drilling capacity in Aluminium ........................................................
Drilling capacity in wood ................................................................
Drill opening range ........................................................................
Drive shank ...................................................................................
Chuck neck diameter .....................................................................
Weight without cable .....................................................................
Typical weighted acceleration in the hand-arm area
Extra handle at front ...................................................................
Rear handle ................................................................................
Motor housing .............................................................................
Typical A-weighted sound levels:
Sound pressure level ..................................................................
Sound power level ......................................................................
Measured values determined according to EN 60 745.
The data stated above apply for models with 230 - 240 V. In case of deviating mains voltage, the data stated on the rating plate are
applicable.
* Measured according to Milwaukee norm N 877318
SAFETY INSTRUCTIONS
Please pay attention to the safety instructions in the attached
leaflet!
Wear ear protectors. Exposure to noise can cause hearing
loss.
Use auxiliary handles supplied with the tool. Loss of control
can cause personal injury.
Appliances used at many different locations including open air must
be connected via a current surge preventing switch.
Always wear goggles when using the machine. It is recommended
to wear gloves, sturdy non slipping shoes and apron.
Sawdust and splinters must not be removed while the machine is
running.
Always disconnect the plug from the socket before carrying out any
work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine. Always
lead the cable away behind you.
When working in 1st gear always use the bow-type handle and/or
the auxialiarhandle. In case the machine is operated with the bow-
type handle, the lower area of the motor housing might be used as
auxiliary handle.
Do not use diamond core drills on hammer mode.
When working in walls ceiling, or floor, take care to avoid electric
cables and gas or waterpipes.
SPECIFIED CONDITIONS OF USE
The electronic drill/screwdriver can be universally used for drilling,
percussion drilling, screwdriving and cutting screw threads.
Do not use this product in any other way as stated for normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in
conformity with the following standards or standardized documents.
EN 60745, EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-
3, in accordance with the regulations 98/37/EC, 89/336/EEC
Manager Product Development
All manuals and user guides at all-guides.com
Volker Siegle
.................................750 W
.................................375 W
............... 0-1200/0-3400 min
-1
........................750/2200 min
-1
.............................54400 min
-1
.............................36000 min
-1
..............................58/30 Nm
...................................20 mm
...................................22 mm
...................................13 mm
...................................16 mm
...................................40 mm
.............................1,5-13 mm
...........................1/2"x20
...................................43 mm
..................................2,7 kg
...................................15 m/s
2
...................................10 m/s
2
.....................................7 m/s
2
...................................98 dB (A)
.................................109 dB (A)
MAINS CONNECTION
Connect only to single-phase a.c. current and only to the system
voltage indicated on the rating plate. It is also possible to connect
to sockets without an earthing contact as the design conforms to
safety class II.
Only use original Milwaukee QUIK-LOK cable.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
If the machine is mainly used for percussion drilling, regularly
remove collected dust from the chuck. To remove the dust hold the
machine with the chuck facing down vertically, and completely
open and close the chuck. The collected dust will fall from the
chuck. It is recommended to regularly use cleaner for the clamping
jaws and the clamping jaw borings.
Use only Milwaukee accessories and Milwaukee spare parts.
Should components need to be replaced which have not been
described, please contact one of our Milwaukee service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the ten-digit No. as well as the machine type printed on the
label and order the drawing at your local service agents or directly
at: Milwaukee Electric Tool, Max-Eyth-Straße 10,
D-71364 Winnenden, Germany.
SYMBOLS
Always disconnect the plug from the socket
before carrying out any work on the machine.
Accessory - Not included in standard equipment,
available as an accessory.
ENGLISH 20