Publicité
Liens rapides
ASME A112.18.1 / CSA B125.1
ASME A112.18.2 / CSA B125.2
ICC/ANSI A117.1
Model/Modelo/Modèle
65305LF-LHP
Baliza™ Series/Series/Seria
Write purchased model number here.
Escriba aquí el número del modelo comprado.
Inscrivez le numéro de modèle ici.
You may need / Usted puede necesitar / Articles dont vous pouvez avoir besoin:
For easy installation of your Brizo
faucet you will need:
• To READ ALL the instructions completely
before beginning.
• To READ ALL warnings, care, and maintenance
information.
• To purchase the correct water supply hook-up.
Para instalación fácil de su llave
Brizo
usted necesitará:
®
• LEER TODAS las instrucciones completamente
antes de empezar.
• LEER TODOS los avisos, cuidados, e
información de mantenimiento.
• Comprar las conexiones correctas para el
suministro de agua.
Pour installer votre robinet Brizo
facilement, vous devez:
• LIRE TOUTES les instructions avant de
débuter;
• LIRE TOUS les avertissements ainsi que toutes
les instructions de nettoyage et d'entretien;
• Acheter le bon nécessaire de raccordement.
www.brizo.com
62325
2.5mm
(3/32")
®
®
62325
1
TWO HANDLE WIDESPREAD
LAVATORY FAUCETS
LLAVES DE LAVAMANOS
EXTENDIDAS DE DOS MANIJAS
ROBINETS À ENTRAXE LONG À
DEUX POIGNÉES POUR LAVABO
?
2.5 mm
(3/32")
06/04/12
Rev. D
Publicité
Manuels Connexes pour Brizo Baliza Serie
Sommaire des Matières pour Brizo Baliza Serie
- Page 1 Inscrivez le numéro de modèle ici. You may need / Usted puede necesitar / Articles dont vous pouvez avoir besoin: 2.5mm (3/32") For easy installation of your Brizo ® faucet you will need: • To READ ALL the instructions completely before beginning.
- Page 2 This warranty excludes all industrial, commercial & business usage, whose purchasers are parts may be obtained by calling 1-877-345-BRIZO (2749) (in the U.S. and Canada) or by hereby extended a five year limited warranty from the date of purchase, with all other terms of writing to: this warranty applying except the duration of the warranty.
- Page 3 RP62786 Lift Rod Barra de Alzar Tige de Manoeuvre RP62771 Handle Base, Gasket & Mounting Nut RP48428 Base para la Manija, Empaque y Aerator & Wrench Tuerca para la Instalación Aireador y Llave Aérateur et Clé Écrou de montage, joint et base de manette RP6060 Bonnet Nuts...
- Page 4 Notes / Notas / Notes 62325 Rev. D...
- Page 5 Remove nut and washer (1) from end valve assemblies. Note: hot side end valve Remove nut and washer (1) from spout (2). Install spout, base (3) and is labeled (5). Slide hot (2) and cold (3) end valves with gaskets (4) through mounting gasket (4).
- Page 6 Step 3b Step 3e Step 3c Remove pivot nut (1). Install horizontal rod (2) and Apply silicone to underside of flange (1). Metal Pop-up stopper (3) as removable (4) or non-removable (5). Insert body (2) into sink. Screw flange (1) Remove stopper (1) and flange (2).
- Page 7 1/2" (13 mm) IPS Install handles onto end valves. For lever handles (1), the stops (2) must point Make Connections to water lines: to the right when installed. For cross handles (3), the stops (2) must point to the center when installed. Be sure glide ring (4) is properly seated in bottom Choose hook-ups for 1/2"...
- Page 8 2.5 mm (3/32") Maintenance f faucet leaks from spout outlet: Shut off water supplies – Replace Seats and Springs (1). * If leak persists: Shut off water supplies – Replace Stem Unit Assembly (2). * Remove aerator (1) using supplied wrench (2) and turn *Install stems (2) and 1/4 turn stops (3) correctly for proper handle rotation: faucet handles (3) to the full on mixed position.