Panasonic EY37A2B Instructions D'installation page 14

EN Setting the clock time manually
1. Make sure the radio is powered on. Press
and hold the Tuning control knob to enter the
Advanced menu of the current mode.
2. Rotate the Tuning control until "CLK" shows
on the display and press the Tuning control
to enter the setting. Now the hour setting
begins flashing.
3. Rotate the Tuning control to select the
desired hour and press the Tuning control to
confirm the setting. Now the minute setting
begins flashing.
4. Rotate the Tuning control to select the
desired minute and press the Tuning control
to confirm the setting. The display will then
revert to the previous menu.
Setting the alarm clock
The radio has two alarms which can each be
set to wake you to AM/FM radio or buzzer
alarm. Ensure the clock time is set before
setting the alarms.
a. Setting radio alarm:
1. Make sure the radio is powered on.
2. Press and hold the radio alarm button, the
radio alarm symbol (
hour will flash followed by a beep.
3. When the hour digit flashes, rotate the
Tuning control to select the required alarm
hour and press the Tuning control to confirm
the hour setting.
4. Then rotate the Tuning control to select the
required alarm minute and press the Tuning
control to confirm the setting.
5. When radio alarm symbol is flashing, rotate
Tuning control to select desired wake-up
band and station, then press Tuning control
to confirm the selection.
6. Rotate Tuning control to select the desired
volume and press Tuning control to confirm
the setting. Radio alarm setting is now
completed.
NOTE:
If the selected AM/FM alarm station is not
available when the alarm is sounding, the
buzzer alarm will be used instead.
b. Setting HWS (Humane Wake System)
buzzer alarm:
1. Make sure the radio is powered on.
2. Press and hold the buzzer alarm button, the
–––––– CLK
) and the display
- 14 -
buzzer alarm symbol (
hour will flash followed by a beep.
3. When the hour digit flashes, rotate the
Tuning control to select the required alarm
hour and press the Tuning control to confirm
the hour setting.
4. Then rotate the Tuning control to select the
required alarm minute and press the Tuning
control to confirm the setting.
5. Rotate Tuning control to select the desired
volume and press Tuning control to confirm
the volume. Buzzer alarm setting is now
completed.
When the alarm sound
To cancel a sounding alarm, press the Power
button.
Disabling/cancelling alarms
To disable an active alarm, press the
corresponding alarm button to cancel the
alarm setting.
Alarm sound duration ––––––––––––– ALM
1. Press and hold the Tuning control to enter
the advanced menu of the current mode.
2. Rotate the Tuning control until "ALM" shows
on the display. Press the Tuning control to
enter the setting.
3. Rotate the Tuning control to cycle through
the option of 1, 3, 5, 10, 15, 30 and 60
minutes. Stop when the desired option
appears on the display, then press the
Tuning control to confirm the setting.
Snooze ––––––––––––––––––––––––– SNZ
1. When the alarm sounds, press any button
other than the Power button will silence the
alarm. Snooze symbol (
the display.
2. To adjust the silence time for the snooze
timer, press and hold the Tuning control to
enter the menu setting.
3. Rotate the Tuning control until "SNZ"
appears on the display, then press the
Tuning control to enter the setting. Rotate the
Tuning control to adjust the silence time from
the options of 1, 3, 5, 10, 15 minutes or OFF
for the snooze timer.
4. To cancel the snooze timer while the alarm
is suspended, press the Power button.
To disable the snooze function, rotate the
Tuning control until "OFF" is displayed.
) and the display
) will appear on