Publicité
Les langues disponibles
Les langues disponibles
POWER BUTTON
1
Touch to turn the washer on and off. Touch to stop/cancel
a cycle at any time.
NOTE: Turning the Wash Cycle knob will also turn the
washer on.
WASH CYCLE KNOB
2
Turn the knob to select a cycle for your laundry load. An LED
will light up for the cycle selected.
NOTE: The Clean Washer with affresh
the washer has run 30 wash cycles as a reminder to run the
Clean Washer with affresh
See "Cycle Guide" for detailed descriptions of cycles.
NOTE: For best results when using the Wash & Dry cycle,
use for loads weighing 2 lbs and less, such as a soccer
uniform or a running tank and shorts. Allow the cycle to
run the full duration of 12 hours.
START BUTTON
3
Touch and hold for 3 seconds until the light above the
Start button comes on to start a cycle, or touch once while a
cycle is in process to pause it. If you want to add a garment,
you can touch the Start button when the "Add Garment"
LED is on.
LED DISPLAY AND SETTINGS
4
When you select a cycle, its default settings will light up and
the Estimated Time Remaining will be displayed. Factors
such as load size, wash temperature, and water pressure
may affect the time shown in the display. Tightly packing,
unbalanced loads, or excessive suds may cause the washer
to lengthen the cycle time, as well.
Touch the desired setting along the bottom of the display
to adjust. See "Cycle Guide" for available settings on each
cycle. Not all settings are available with all cycles.
Cycle Status Lights
For details, see "Cycle Status Lights" section.
Load & Go
– Detergent Concentration
™
and Water Hardness (on some models)
Touch DETERGENT CONCENTRATION to set detergent
concentration from 2x to 6x. Touch WATER HARDNESS
to set water hardness (normal, hard, or soft). For details,
see "About Detergent Concentration" section.
IMPORTANT: When using the dispenser cartridge with
concentrated liquid detergent, be sure to change the
detergent concentration settings in the control if the
detergent used is different than factory preset of 2x
concentration.
Wash Temp
The recommended wash temperature is preset for each
cycle. You may also select a wash temperature based
on the type of fabric and soils being washed. For best
results, use the warmest wash water safe for your
fabric, following the garment label instructions.
All wash temperatures feature a cold rinse.
Spin
This washer automatically selects the spin speed
based on the cycle selected. Some preset speeds
can be changed.
Faster spin speeds mean shorter dry times, but may
n
increase wrinkling in your load.
Slower spin speeds reduce wrinkling, but will leave
n
your load more damp.
6
All manuals and user guides at all-guidesbox.com
LED will flash when
®
®
cycle.
Soil
Soil level (wash time) is preset for each wash cycle.
When you change the soil setting, the cycle time will
increase or decrease in the Estimated Time Remaining
display.
For most loads, use the soil level that is preset with
the cycle you have chosen. For heavily soiled and
sturdy fabrics, use the Soil setting to select more wash
time. For lightly soiled and delicate fabrics, use the
Soil setting to select less wash time. Lower soil level
settings will help reduce tangling and wrinkling.
Presoak
Touch to add a Presoak time of your choice to a
wash cycle. Items will gently tumble through the
detergent and water for the selected time to help
loosen tough stains.
OPTIONS
5
Touch to activate additional wash options or additional
features on the washer before touching the Start button.
Additional wash options or additional features selected
after touching the Start button may not activate.
Once a wash option or additional feature is selected, it is
saved for the cycle selected. To return to factory default
cycle settings, unplug washer for 30 seconds; then
plug back in.
Adjust Delay Time
A
–
+
Touch
or
to delay the start of the wash cycle by up
to 8 to 12 hours depending on your model.
FanFresh
Option (on some models)
®
B
The FanFresh
option will periodically tumble the load
®
after the end of the cycle for up to 12 hours, while the
integrated fan circulates air through the washer to
reduce humidity. To turn on the FanFresh
FANFRESH. If, however, the FanFresh
on, it will stay on for all future cycles until turned back
off – the washer remembers the last on/off status set.
To turn off the FanFresh
You may also activate the FanFresh
running a cycle by touching and holding the Power
button for one second, then touching and holding
FANFRESH for 3 seconds, then touching and holding
the Start button for 3 seconds.
To turn off the FanFresh
touch the Power button.
NOTE: The door will lock while the FanFresh
is active. To cancel the option and unlock the door,
touch the Power button.
Extra Rinse
C
Activate this option to add an extra rinse to most cycles.
NOTE: Extra Rinse can also be used to turn on the
Drum Light (on some models). Simply touch and hold
EXTRA RINSE for 3 seconds.
option, touch
®
®
option is turned
option, touch FANFRESH.
®
®
option without
option when it is running,
®
option
®
Publicité
