Bosch EasyHedgeCut 18V-45 Notice Originale page 15

– Sound pressure level
– Sound power level
– Uncertainty K
Vibration total values ah (triax vector sum) and uncertainty K determined
according to EN 62841-4-2:2019
– Vibration emission value a
h
– Uncertainty K
That the declared vibration total value(s) and the declared
noise emission value(s) have been measured in accordance
with a standard test method and may be used for comparing
one machine with another.
That the declared vibration total value(s) and the declared
noise emission value(s) may also be used in a preliminary as-
sessment of exposure.
That the vibration and noise emissions during actual use of
the machine can differ from the declared total value depend-
ing on the ways in which the machine is used; and of the
need to identify safety measures to protect the operator that
are based on an estimation of exposure in the actual condi-
tions of use (taking account of all parts of the operating cycle
such as the times when the machine is switched off and
when it is running idle in addition to the trigger time).
Switching on
For Your Safety
Caution: Switch garden tool off and remove battery
u
from machine before adjusting or cleaning.
The blades continue to move for a fraction of a second
u
after the hedge trimmer is switched off.
Do not touch the moving blades.
u
Charging the Battery
Pay attention to the mains voltage. The voltage of the
u
power source must match the voltage specified on the
rating plate of the charger.
The battery is equipped with temperature monitoring that al-
lows charging only in the temperature range between 0 °C
and 35 °C. In this manner, a high battery service life is
achieved.
Note: The battery is supplied partially charged. To ensure
full battery capacity, completely charge the battery in the
battery charger before using for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not cause damage to the battery.
The "Electronic Cell Protection (ECP)" protects the lithium-
ion battery against deep discharging. When the battery is
empty, the product is switched off by means of a protective
circuit: The product no longer operates.
Bosch Power Tools
3 600 H49 H..
dB(A) 74
dB(A) 82
dB 2.0
2
m/s 2.5
2
m/s 1.5
Do not continue to press the On/Off switch after an auto-
matic shut-off of the product. The battery could become
damaged.
Observe the notes for disposal of the battery.
Inserting/Removing the Battery (see figure B)
Note: Using unsuitable batteries can lead to malfunctions or
damage the machine.
Insert the charged battery (8). Ensure the battery is inserted
correctly.
To remove the battery (8) from the machine, press the bat-
tery unlocking button (7) and pull the battery out.
Operation
Switching On and Off (see figures C − D)
As soon as the battery is inserted and a clicking sound can
be heard (see figure B) simultaneously press the front
switch (2) and the switch at the rear handle (1).
In order to switch the device off, either release the switch at
the rear handle (1) or the switch at the front handle (2) or
both at the same time.
Working with the Hedgecutter (see figure E)
Move the hedgecutter evenly forward along the cutting line.
The double edge cutting blade enables cutting in either dir-
ection, or with a side to side motion.
Cut the sides of the hedge first, then the top.
To cut the sides straightly, we recommend cutting from bot-
tom to top in the direction of growth. Younger stems tend to
move outwards when cutting them from top to bottom, res-
ulting in shallow patches or holes in the hedge.
To reach a level finish, fasten a piece of string along the
length of the hedge at the required height and use as an
alignment guide. Cut the hedge just above the string.
Pay attention that no objects such as wires are cut. The
blade or drive can be damaged.
Anti Blocking
If the blade stalls on a tough material, the load of the motor
increases. The intelligent micro-electronics senses this over-
load condition and repeatedly reverses the motor, in order
to prevent stalling and to cut the branch through.
This audible reversing cut action continues for up to 3 s.
English | 15
3 600 H49 M.. 3 600 H49 H..
76
84
2.0
2.5
1.5
F 016 L94 401 | (26.10.2022)
74
82
2.0
2.5
1.5